Harmonization of Apprenticeship Training

Provincial and territorial apprenticeship authorities are each responsible for their respective apprenticeship programs. In the spirit of continual improvement, and to facilitate mobility among apprentices in Canada, participating authorities have agreed to work towards harmonizing certain aspects of their programs where possible. After consulting with their stakeholders in the trade, they have reached consensus on the following elements. Note that implementation of these elements may vary from jurisdiction to jurisdiction, depending on their own circumstances. For more information on the implementation in any province and territory, please contact that jurisdiction’s apprenticeship authority.

1. Trade name

The official Red Seal name for this trade is Machinist.

2. Number of Levels of Apprenticeship

The number of levels of technical training recommended for this trade is 4 (four).

3. Total Training Hours During Apprenticeship Training

The total hours of training, including both on-the-job and in-school training for this trade is 7200.

4. Sequencing Topics and Related Sub-tasks

The topic titles in the table below are placed in a column for each apprenticeship level for technical training. Each topic is accompanied by the sub-tasks and their reference number. The topics in the grey shaded cells represent those that are covered “in context” with other training in the subsequent years.

Sequencing Topics and Related Sub-tasks
Level 1 Level 2 Level 1 Level 2
  Organizes Work in context Organizes Work in context Organizes Work in context
  Communication and Mentoring in context Communication and Mentoring in context Communication and Mentoring in context
  Hand Processes in context    
      Machine and Tooling Maintenance in context
    Component Refurbishment in context Component Refurbishment in context
Safety-Related Tasks
  • 1.01 Maintain safe work environment
  • 1.02 Use PPE and safety equipment
Safety-Related Tasks
  • 1.01 Maintain safe work environment
Safety-Related Tasks
  • 1.01 Maintain safe work environment
Safety-Related Tasks
  • 1.01 Maintain safe work environment
Organizes Work
  • 2.01 Interprets documentation
  • 2.02 Plans sequence of operation
     
Communication and Mentoring
  • 3.01 Uses communication techniques
  • 3.02 Uses mentoring techniques
     
Workpiece Material Processing
  • 4.01 Selects workpiece material
  • 4.02 Uses hoisting, lifting and rigging equipment
  • 4.03 Marks workpiece for identification
  • 4.05 Performs quality control of workpiece
  • 4.06 Deburrs workpiece
  • 4.07 Sketches parts
Workpiece Material Processing
  • 4.01 Selects workpiece material
  • 4.04 Performs heat treatment
  • 4.05 Performs quality control of workpiece
  • 4.07 Sketches parts
Workpiece Material Processing
  • 4.04 Performs heat treatment
  • 4.05 Performs quality control of workpiece
Workpiece Material Processing
  • 4.05 Performs quality control of workpiece
Machine and Tooling Maintenance
  • 5.01 Cleans machines
  • 5.02 Lubricates machines
  • 5.03 Sharpens tooling
  • 5.04 Applies cutting fluid and coolant
  • 5.05 Troubleshoots equipment
  • 5.06 Maintains machine alignment
  • 5.07 Maintains inspection equipment
Machine and Tooling Maintenance
  • 5.01 Cleans machines
  • 5.05 Troubleshoots equipment
  • 5.06 Maintains machine alignment
Machine and Tooling Maintenance
  • 5.03 Sharpens tooling
  • 5.05 Troubleshoots equipment
 
Hand Processes
  • 6.01 Performs Layout
  • 6.02 Saws workpiece
  • 6.03 Files workpiece
  • 6.04 Performs hole making operations
  • 6.05 Performs threading operations
  • 6.06 Installs thread inserts
  • 6.07 Broaches workpiece
  • 6.08 Performs pressing operations
  • 6.09 Forms workpiece
  • 6.10 Finishes workpiece
     
Components (Introduction)
  • 7.01 Disassembles components
  • 7.02 Analyzes components
Component Refurbishment
  • 7.02 Analyzes components
  • 7.03 Assembles components
   
Power Saw Setup
  • 8.01 Selects power saw types
  • 8.02 Selects saw blades
  • 8.03 Installs saw blades
  • 8.04 Selects power saw speeds and feeds
  • 8.05 Makes power saw adjustments
  • 8.06 Sets up workpiece on power saw
     
Power Saw Operation
  • 9.01 Saws straight and angle cuts
  • 9.02 Cuts irregular shapes
     
Drill Press Setup
  • 10.01 Selects drill press types
  • 10.02 Plans operation of drill presses
  • 10.03 Selects drill press speeds and feeds
  • 10.04 Sets up jig, fixtures and work holding devices for drill presses
  • 10.05 Sets up tooling for drill presses
     
Drill Press Operation
  • 11.01 Drills holes using a drill press
  • 11.02 Cuts countersinks, counterbores, chamfers and spot faces using a drill press
  • 11.03 Performs tapping using a drill press
  • 11.04 Finishes holes using a drill press
     
Conventional Lathe Setup
  • 12.01 Selects conventional lathes types
  • 12.02 Plans operation of conventional lathes
  • 12.03 Sets up work holding devices for conventional lathes
  • 12.04 Sets up tooling for conventional lathes
  • 12.05 Sets up conventional lathe accessories
  • 12.06 Sets up workpiece on conventional lathe
  • 12.07 Selects conventional lathe speeds and feeds
Conventional Lathe Setup
  • 12.02 Plans operation of conventional lathes
  • 12.03 Sets up work holding devices for conventional lathes
  • 12.04 Sets up tooling for conventional lathes
  • 12.05 Sets up conventional lathe accessories
  • 12.06 Sets up workpiece on conventional lathe
   
Conventional Lathe Operation
  • 13.01 Faces surfaces using a conventional lathe
  • 13.02 Turns external surfaces using a conventional lathe
  • 13.03 Drills using a conventional lathe
  • 13.04 Bores holes using a conventional lathe
  • 13.05 Reams holes using a conventional lathe
  • 13.06 Turns tapers using a conventional lathe
  • 13.07 Knurls using a conventional lathe
  • 13.08 Cuts grooves using a conventional lathe
  • 13.09 Cuts threads using a conventional lathe
  • 13.10 Parts off workpiece using a conventional lathe
Conventional Lathe Operation
  • 13.02 Turns external surfaces using a conventional lathe
  • 13.04 Bores holes using a conventional lathe
  • 13.06 Turns tapers using a conventional lathe
  • 13.08 Cuts grooves using a conventional lathe
  • 13.09 Cuts threads using a conventional lathe
   
Conventional Milling Machine (Introduction)
  • 14.01 Selects conventional milling machine types
  • 14.04 Sets up tooling for conventional milling machines
Conventional Milling Machine Setup
  • 14.01 Selects conventional milling machine types
  • 14.02 Plans operation of milling machines
  • 14.03 Sets up work holding devices for conventional milling machines
  • 14.04 Sets up tooling for conventional milling machines
  • 14.05 Sets up milling accessories
  • 14.06 Sets up workpiece on a conventional milling machine
  • 14.07 Selects conventional milling machine speeds and feeds
Conventional Milling Machine Setup
  • 14.02 Plans operation of milling machines
  • 14.03 Sets up work holding devices for conventional milling machines
  • 14.04 Sets up tooling for conventional milling machines
  • 14.05 Sets up milling accessories
  • 14.06 Sets up workpiece on a conventional milling machine
  • 14.07 Selects conventional milling machine speeds and feeds
Conventional Milling Machine Setup
  • 14.05 Sets up milling accessories
  Conventional Milling Machine Operation
  • 15.01 Mills surfaces using a conventional milling machine
  • 15.02 Mills profiles and pockets using a conventional milling machine
  • 15.03 Mills slots, grooves and keyways using a conventional milling machine
  • 15.04 Cuts gears and splines using a conventional milling machine (indexing calculations)
  • 15.05 Drills holes using a conventional milling machine
  • 15.06 Reams holes using a conventional milling machine
  • 15.07 Cuts countersinks, counterbores, chamfers and spot faces using a conventional milling machine
  • 15.08 Performs tapping using a conventional milling machine
  • 15.09 Bores holes using a conventional milling machine
Conventional Milling Machine Operation
  • 15.01 Mills surfaces using a conventional milling machine
  • 15.02 Mills profiles and pockets using a conventional milling machine
  • 15.03 Mills slots, grooves and keyways using a conventional milling machine
  • 15.04 Cuts gears and splines using a conventional milling machine
  • 15.09 Bores holes using a conventional milling machine
Conventional Milling Machine Operation
  • 15.04 Cuts gears and splines using a conventional milling machine
  Precision Grinding Machine Setup
  • 16.01 Selects precision grinding machine types
  • 16.02 Plans operation of grinding machines
  • 16.03 Sets up work holding devices for precision grinding machines
  • 16.04 Mounts grinding wheel
  • 16.05 Sets up grinding accessories
  • 16.06 Sets up workpiece on precision grinding machines
  • 16.07 Selects precision grinding machine speeds and feeds
Precision Grinding Machine Setup
  • 16.01 Selects precision grinding machine types
  • 16.02 Plans operation of grinding machines
  • 16.03 Sets up work holding devices for precision grinding machines
  • 16.04 Mounts grinding wheel
  • 16.05 Sets up grinding accessories
  • 16.06 Sets up workpiece on precision grinding machines
  • 16.07 Selects precision grinding machine speeds and feeds
 
  Precision Grinding Machine Operation
  • 17.01 Grinds flat surfaces using a surface grinder
Precision Grinding Machine Operation
  • 17.02 Grinds profiles
  • 17.03 Grinds internal and external cylindrical and tapered surfaces
  • 17.04 Grinds tools and cutters
  • 17.05 Finishes holes using a honing machine
 
  CNC Programming
  • 18.01 Creates process documentation
  • 18.02 Creates manual input program
  • 18.03 Transfers program to and from control memory
CNC Programming
  • 18.01 Creates process documentation
  • 18.02 Creates manual input program
  • 18.04 Optimizes program
  • 18.05 Creates 2D and 3D models
  • 18.06 Programs using CAM
CNC Programming
  • 18.04 Optimizes program
  • 18.05 Creates 2D and 3D models
  • 18.06 Programs using CAM
  CNC Machine Setup
  • 19.01 Selects tooling and tool holders for CNC machines
  • 19.02 Sets up tooling and tool holders on CNC machines
  • 19.03 Sets up workpiece on CNC machines
  • 19.04 Establishes work datum
  • 19.05 Verifies program
CNC Machine Setup
  • 19.01 Selects tooling and tool holders for CNC machines
  • 19.02 Sets up tooling and tool holders on CNC machines
  • 19.03 Sets up workpiece on CNC machines
  • 19.04 Establishes work datum
CNC Machine Setup
  • 19.03 Sets up workpiece on CNC machines
  CNC Machine Operation
  • 20.01 Adjusts offsets
  • 20.02 Monitors machining processes
  • 20.03 Interrupts program cycle
  • 20.04 Restarts program cycle
CNC Machine Operation
  • 20.01 Adjusts offsets
CNC Machine Operation
  • 20.01 Adjusts offsets