Table of contents
Task B-7 Fabricates commercial window and door systems
Task descriptor
Glaziers are responsible for the fabrication of window and door systems for commercial projects. Fabrication takes place in the fabrication shop or on site prior to installation.
B-7.01 Fabricates curtain walls
B-7.01 Fabricates curtain walls
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-7.01.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task, manufacturers’ specifications and system requirements |
B-7.01.02P |
create and use jigs and templates |
jigs and templates are created and used according to manufacturers’ specifications and system requirements |
B-7.01.03P |
measure frame components |
frame components are measured according to shop drawings |
B-7.01.04P |
cut curtain wall components |
curtain wall components are cut from stock length extrusions and materials according to system requirements |
B-7.01.05P |
lay out mullions |
mullions are laid out according to shop drawings |
B-7.01.06P |
assemble frames and components |
frames and components are assembled according to specifications |
B-7.01.07P |
install setting and dam blocks for stick built and pre-glazed unitized units |
setting blocks for stick built and pre-glazed unitized units are installed according to system requirements |
B-7.01.08P |
install back pans |
back pans are installed according to system requirements |
B-7.01.09P |
make vent and drain holes in pressure plates |
vent and drain holes in pressure plates are made according to manufacturers’ specifications |
B-7.01.10P |
install vinyl and tape |
vinyl and tape are installed according to manufacturers’ specifications |
B-7.01.11P |
install glass into frames |
glass is installed into frames according to manufacturers’ specifications |
B-7.01.12P |
install pressure plates, sealants and screws |
pressure plates, sealants and screws are installed to secure glass to frames according to manufacturers’ specifications and system requirements |
B-7.01.13P |
prepare products for shipping |
products are prepared for shipping according to industry standards |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- system requirements include: shop drawings, envelope consultants
- components include: spigots, stops, mullions, muntins, glass, flashing, tapes, rubbers
- lay out includes: spigot locations, pilot holes, horizontal locations
- vinyl and tape include: back vinyl, thermal break, vinyl pressure plates, glazing tape, foam tape
- sealants include: structural silicone glazing (SSG), caulking
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-7.01.01L |
demonstrate knowledge of curtain walls, their components, characteristics and applications |
identify types of curtain walls and their components, and describe their characteristics and applications |
describe manufacturers’ specifications related to expansion and contraction |
describe location of weep holes, vent ports and anchors, and describe their characteristics and applications |
identify types of operable windows and describe their characteristics and applications |
B-7.01.02L |
demonstrate knowledge of procedures used to fabricate curtain walls |
identify tools and equipment used to fabricate curtain walls, and describe their applications and procedures for use |
interpret instructions used to assemble curtain walls |
describe procedures used to fabricate curtain walls |
describe fabrication sheets and describe their characteristics and applications |
identify types of sealants, gaskets and tapes and describe their characteristics and applications |
B-7.01.03L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- components include: spigots, stops, mullions, muntins, glass, flashing, tapes, rubbers
- types of curtain walls include: two‑sided, four‑sided SSG, stick-built, pre-glazed unitized systems
- types of operable windows include: casement, awning, hopper
- tools and equipment include: see Appendix B (Tools and Equipment)
- sealants include: structural silicone glazing (SSG), caulking
- codes and regulations include: National Building Code of Canada (NBC), National Energy Code for Buildings (NECB), jurisdictional codes and regulations
B-7.02 Fabricates storefronts
B-7.02 Fabricates storefronts
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-7.02.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task, manufacturers’ specifications and system requirements |
B-7.02.02P |
create and use jigs and templates |
jigs and templates are created and used according to manufacturers’ specifications and system requirements |
B-7.02.03P |
measure storefront components |
storefront components are measured according to shop drawings |
B-7.02.04P |
cut storefront components |
storefront components are cut from stock extrusions and materials according to manufacturers’ specifications and system requirements |
B-7.02.05P |
lay out mullions |
mullions are laid out according to shop drawings |
B-7.02.06P |
assemble frames and components |
frames and components are assembled according to manufacturers’ specifications |
B-7.02.07P |
prepare products for shipping |
products are prepared for shipping according to industry standards |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- system requirements include: shop drawings, envelope consultants
- components include: mullions, muntins, rain deflectors, glazing stops, gaskets, sill, flashing, spigots
- lay out includes: spigot locations, pilot holes, horizontal locations
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-7.02.01L |
demonstrate knowledge of storefronts, their characteristics and applications |
identify types of storefronts and describe their characteristics and applications |
describe amount of pre-assembly done in shop |
B-7.02.02L |
demonstrate knowledge of procedures used to fabricate storefronts |
identify tools and equipment used to fabricate storefronts and describe their applications and procedures for use |
describe procedures used to fabricate storefronts |
identify types of materials used in fabrication of storefronts |
describe fasteners used in fabrication of storefronts |
B-7.02.03L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- applications include: interior, exterior
- types of storefronts include: thermally broken, non-thermally broken, flush-glazed
- tools and equipment include: see Appendix B (Tools and Equipment)
- materials include: extrusion, vinyl, sealants, sheet metal
- fasteners include: screws, nuts and bolts, pop rivets
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations
B-7.03 Fabricates window systems
B-7.03 Fabricates window systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-7.03.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task, manufacturers’ specifications and system requirements |
B-7.03.02P |
create and use jigs and templates |
jigs and templates are created and used according to manufacturers’ specifications and system requirements |
B-7.03.03P |
measure window system components |
window system components are measured according to shop drawings |
B-7.03.04P |
cut window system components |
window system components are cut from stock length extrusions and materials according to manufacturers’ specifications and system requirements |
B-7.03.05P |
lay out mullions |
mullions are laid out according to shop drawings |
B-7.03.06P |
assemble frames and window system components |
frames and window system components are assembled according to manufacturers’ specifications and shop drawings |
B-7.03.07P |
prepare products for shipping |
products are prepared for shipping according to industry standards |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- system requirements include: shop drawings, envelope consultants
- window system components include: jambs, headers, sills, spigots, hardware, glazing, stops
- lay out includes: spigot locations, pilot holes, horizontal locations
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-7.03.01L |
demonstrate knowledge of window systems, their components, characteristics and applications |
identify types of window systems and their components, and describe their characteristics and applications |
identify types of operable windows and describe their characteristics and applications |
B-7.03.02L |
demonstrate knowledge of procedures used to fabricate window systems |
identify tools and equipment used to fabricate window systems and describe their applications and procedures for use |
describe procedures used to fabricate window systems |
describe amount of pre-assembly done in shop |
identify types of weather seal materials and describe their characteristics and applications |
identify types of sealants and describe their characteristics and applications |
identify types of finishes and describe their characteristics and applications |
identify types of fasteners and describe their characteristics and applications |
describe thermal breaks |
B-7.03.03L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- window system components include: jambs, headers, sills, spigots, hardware, glazing, stops
- types of window systems include: strip (ribbon), window wall, punched opening
- types of operable windows include: casement, awning, hopper
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of weather seal materials include: tapes, sealants, gaskets
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations
B-7.04 Fabricates skylights and sloped glazing systems
B-7.04 Fabricates skylights and sloped glazing systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-7.04.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task, manufacturers’ specifications and system requirements |
B-7.04.02P |
create and use jigs and templates |
jigs and templates are created and used according to manufacturers’ specifications and system requirements |
B-7.04.03P |
measure frame components |
frame components are measured according to shop drawings |
B-7.04.04P |
cut and notch skylights and sloped glazing systems components |
skylights and sloped glazing components are cut and notched from stock length extrusions and materials according to system requirements |
B-7.04.05P |
lay out rafters and purlins |
rafters and purlins are laid out according to shop drawings |
B-7.04.06P |
prepare products for shipping |
products are prepared for shipping according to industry standards |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- system requirements include: shop drawings, envelope consultants
- components include: rafters, purlins, spigots, splice plates, pressure plates, gutters, sleeve anchors, condensation gutters, compression rings, fasteners, flashings, gaskets
- lay out includes: spigot locations, pilot holes, horizontal locations
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-7.04.01L |
demonstrate knowledge of skylights, sloped glazing systems and their components, characteristics and applications |
identify types of skylights and sloped glazing systems and their components, and describe their characteristics and applications |
B-7.04.02L |
demonstrate knowledge of procedures used to fabricate skylights and sloped glazing systems |
identify tools and equipment used to fabricate skylights and sloped glazing systems and describe their applications and procedures for use |
describe procedures used to fabricate skylights and sloped glazing systems |
describe amount of pre-assembly done in shop |
identify types of weather seal materials and describe their characteristics and applications |
identify types of flashings and describe their characteristics and applications |
identify types of anchors and describe their characteristics and applications |
identify types of membranes and describe their characteristics and applications |
identify types of sealants and describe their characteristics and applications |
describe skylight and sloped glazing construction techniques |
describe requirements for substrate to aluminum separation |
B-7.04.03L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- types of skylights and sloped glazing systems include: ridge, hip, pyramid, barrel vault, T-bar, pressure cap
- components include: rafters, purlins, spigots, splice plates, pressure plates, gutters, sleeve anchors, condensation gutters, compression rings, fasteners, flashings, gaskets
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of weather seal materials include: tapes, sealants, flashings, gaskets, self-adhered membrane
- types of flashings include: primary, secondary
- types of anchors include: sleeve, welded, bolted
- requirements for substrate to aluminum separation include: shims, bituminous paint, membrane, slip pads
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations
B-7.05 Fabricates entrance systems
B-7.05 Fabricates entrance systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-7.05.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task, manufacturers’ specifications and system requirements |
B-7.05.02P |
create and use jigs and templates |
jigs and templates are created and used according to manufacturers’ specifications and system requirements |
B-7.05.03P |
measure entrance system components |
entrance system components are measured according to shop drawings and site conditions |
B-7.05.04P |
cut and mortice entrance system components |
entrance system components are cut from stock length extrusions and materials according to manufacturers’ specifications and system requirements |
B-7.05.05P |
lay out entrance system components |
entrance system components are laid out according to shop drawings |
B-7.05.06P |
assemble entrance system components |
entrance system components are assembled according to manufacturers’ specifications |
B-7.05.07P |
prepare products for shipping |
products are prepared for shipping according to industry standards |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- system requirements include: shop drawings, envelope consultants
- components include: handles, closers, thresholds, bolts, maximum security (MS) locks, locksets, electric strikes, panic hardware (exit devices), mullions, muntins, glass, pivots, hinges
- lay out includes: spigot locations, pilot holes, horizontal locations, rail locations, hardware locations
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-7.05.01L |
demonstrate knowledge of entrance systems, their components, characteristics and applications |
identify types of entrance systems and their components, and describe their characteristics and applications |
identify types of automatic door operators and describe their characteristics and applications |
B-7.05.02L |
demonstrate knowledge of procedures used to fabricate entrance systems |
interpret instructions, templates, manufacturers’ specifications and drawings |
identify tools and equipment used to fabricate entrance systems and describe their applications and procedures for use |
describe procedures used to fabricate entrance systems |
identify types of framing materials and describe their characteristics and applications |
identify types of hardware and describe their characteristics and applications |
explain compatibility and performance for types of specified hardware for aluminum doors |
identify types of gaskets and describe their characteristics and applications |
B-7.05.03L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- components include: handles, closers, thresholds, bolts, maximum security (MS) locks, locksets, electric strikes, panic hardware (exit devices), mullions, muntins, glass, pivots, hinges
- types of entrance systems include: swing, bifold, revolving, sliding, portals, vestibule, total vision system (TVS)
- types of automatic door operators include: electric, pneumatic, hydraulic
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of framing materials include: flush glaze, curtain wall with door adapter, storefront
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations
Task B-8 Installs commercial window and door systems
Task descriptor
Glaziers are responsible for the installation of window and door systems for commercial projects. This could include new construction or retrofit projects.
B-8.01 Lays out commercial window and door systems
B-8.01 Lays out commercial window and door systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-8.01.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task and manufacturers’ specifications |
B-8.01.02P |
measure rough openings and confirm sizing |
rough openings are measured according to site conditions and sizing is confirmed according to shop drawings |
B-8.01.03P |
locate benchmarks and gridlines |
benchmarks and gridlines are located according to architectural drawings and general contractor |
B-8.01.04P |
lay out window and door systems |
window and door systems are laid out according to architectural drawings |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-8.01.01L |
demonstrate knowledge of procedures used to lay out commercial window and door systems |
identify tools and equipment used to lay out commercial window and door systems, and describe their applications and procedures for use |
identify types of window systems, and describe their characteristics and applications |
describe procedures used to measure and assess rough openings |
describe procedures used to transfer lines from floor to ceiling and roof |
describe procedures used to create offset lines |
describe procedures used to transfer benchmarks |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of window systems include: strip (ribbon), curtain wall, storefront, TVS
B-8.02 Installs curtain wall systems
B-8.02 Installs curtain wall systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-8.02.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task and manufacturers’ specifications |
B-8.02.02P |
install starter tracks and anchors |
starter tracks and anchors are installed according to layout |
B-8.02.03P |
install curtain walls |
curtain walls are installed according to shop drawings and manufacturers’ specifications |
B-8.02.04P |
air seal perimeter |
perimeter is air sealed according to shop drawings, jurisdictional codes and regulations, and manufacturers’ specifications |
B-8.02.05P |
install corner blocks for horizontally drained stick-built systems |
corner blocks for horizontally drained stick-built systems are installed according to manufacturers’ specifications |
B-8.02.06P |
install gasket (wet or dry) in stick-built systems |
gasket (wet or dry) is installed according to manufacturers’ specifications |
B-8.02.07P |
install glass in stick-built systems |
glass is installed according to shop drawings |
B-8.02.08P |
finish frames and glass with pressure plates, caps and sealants |
frames and glass are finished with pressure plates, caps and sealants according to shop drawings |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- gaskets include: vinyl, shim tape, high-density foam tape
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-8.02.01L |
demonstrate knowledge of curtain wall systems, their components, characteristics and applications |
identify types of curtain wall systems and their components, and describe their characteristics and applications |
identify types of substrates |
identify types of gaskets |
explain rain screen principle |
describe wet and dry curtain wall systems and benefits of each |
identify types of anchoring systems and describe their characteristics and applications |
describe purpose of wind (live) load and dead load anchors |
B-8.02.02L |
demonstrate knowledge of procedures used to install curtain wall systems and their components |
identify tools and equipment used to install curtain wall systems and their components, and describe their applications and procedures for use |
describe procedures used to install curtain wall systems and their components |
explain tolerances when installing curtain walls |
describe procedures used to allow for expansion and contraction when installing window systems |
describe procedures used to assemble curtain wall systems on-site |
identify types of primers used for self-adhered membrane, polyurethane and silicone |
identify types of sealants and describe their characteristics, compatibility and applications |
Range of variables
- components include: pressure plates, caps, anchors, shear blocks, dam blocks, back pans, gaskets, fasteners, glass
- types of curtain wall systems include: captured, two‑sided, four‑sided SSG, stick-built, pre-glazed unitized
- types of substrates include: concrete, wood, steel, masonry
- gaskets include: vinyl, shim tape, high-density foam tape
- types of anchoring systems include: starter tracks, welded anchors, slip anchors, embeds, bolster blocks/anchor backup assembly, sill/perimeter angle
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of sealants include: butyl, silicone, polyurethane
B-8.03 Installs storefront systems
B-8.03 Installs storefront systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-8.03.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task and manufacturers’ specifications |
B-8.03.02P |
install components |
components are installed according to manufacturers’ specifications and shop drawings |
B-8.03.03P |
plumb, level and square frames |
frames are plumbed, levelled and squared using shims |
B-8.03.04P |
secure frames in place |
frames are secured in place using fasteners |
B-8.03.05P |
perform on-site glazing |
glazing is performed on-site |
B-8.03.06P |
install glass stops and gaskets |
glass stops and gaskets are installed according to shop drawings |
B-8.03.07P |
apply perimeter sealants |
perimeter sealants are applied according to shop drawings |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- components (storefront systems)include: deflection header, sills, sub-sills, rain deflectors, back-up plates, stops, verticals, horizontals
- fasteners include: screws, plugs
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-8.03.01L |
demonstrate knowledge of storefront systems, their components, characteristics and applications |
identify types of storefront systems, their components and describe their characteristics and applications |
describe the amount of assembly done on-site |
B-8.03.02L |
demonstrate knowledge of entrance systems and their components |
identify types of entrance systems and their components |
B-8.03.03L |
demonstrate knowledge of procedures used to install storefront systems |
identify tools and equipment used to install storefronts systems and describe their applications and procedures for use |
describe procedures used to install storefront systems |
identify types of hardware and describe their characteristics and applications |
identify types of glazing gaskets and describe their characteristics and applications |
B-8.03.04L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- components (storefront systems)include: deflection header, sills, sub-sills, rain deflectors, back-up plates, stops, verticals, horizontals
- applications include: interior, exterior
- types of storefront systems include: single glaze, double glaze, thermally broken, non-thermally‑broken
- components (entrance systems) include: handles, closers, thresholds, flush bolts, locksets, electric strikes, panic hardware (exit devices), pivots, restrictors
- types of entrance systems include: swing, bifold, revolving, sliding, portals, vestibule, TVS
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of glazing gaskets include: vinyl, rubber, tapes
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations
B-8.04 Installs window systems
B-8.04 Installs window systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-8.04.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task and manufacturers’ specifications |
B-8.04.02P |
assemble components |
components are assembled according to manufacturers’ specifications |
B-8.04.03P |
plumb, level and square window systems |
window systems are plumbed, levelled and squared using shims |
B-8.04.04P |
secure window systems |
window systems are secured using screws, plugs or anchors |
B-8.04.05P |
install setting blocks when glazing windows on-site |
setting blocks are installed according to manufacturers’ specifications when glazing windows on-site |
B-8.04.06P |
perform on-site glazing |
glazing is performed on-site |
B-8.04.07P |
secure glass |
glass is secured using glass stops |
B-8.04.08P |
insulate and seal frame |
frame is insulated and sealed according to shop drawings |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- components include: jambs, headers, sills, spigots, hardware, glazing, stops, rain screen components
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-8.04.01L |
demonstrate knowledge of window systems, their components, characteristics and applications |
identify types of window systems and their components, and describe their characteristics and applications |
describe procedures used to install glass stops, and describe their characteristics and applications |
B-8.04.02L |
demonstrate knowledge of procedures used to install window systems and their components |
identify tools and equipment used to install window systems and describe their applications and procedures for use |
describe procedures used to install window systems |
identify types of weather seal materials |
identify methods of assembly of window systems |
B-8.04.03L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- components include: jambs, headers, sills, spigots, hardware, glazing, stops, rain screen components
- types of window systems include: strip (ribbon), window wall
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of weather seal materials include: tapes, sealants, gaskets
- methods of assembly of window systems include: pre-glazed, site-glazed
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations
B-8.05 Installs skylights and sloped glazing systems
B-8.05 Installs skylights and sloped glazing systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-8.05.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task and manufacturers’ specifications |
B-8.05.02P |
measure opening for skylights and sloped glazing and confirm sizing |
opening for skylights and sloped glazing is measured and sizing is confirmed according to shop drawings |
B-8.05.03P |
place and assemble condensation gutters and frame members |
condensation gutters and frame members are placed and assembled according to manufacturers’ specifications and shop drawings |
B-8.05.04P |
install components |
components are installed according to manufacturers’ specifications and shop drawings |
B-8.05.05P |
position skylights and sloped glazing |
skylights and sloped glazing are positioned according to shop drawings, site conditions and manufacturers’ specifications |
B-8.05.06P |
secure anchors |
anchors are secured using fasteners according to manufacturers’ specifications and shop drawings |
B-8.05.07P |
install insulation |
insulation is installed between primary and secondary flashing according to shop drawings |
B-8.05.08P |
perform on-site glazing |
glazing is performed on-site |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- components include: rafters, purlins, purlin bars/pressure caps, spigots, splice plates, pressure plates and caps, gutters, sleeve anchors
- fasteners include: bolts, screws, rivets
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-8.05.01L |
demonstrate knowledge of skylights and sloped glazing systems, their components, characteristics and applications |
identify types of skylights and sloped glazing systems and their components, and describe their characteristics and applications |
identify types of weather seal materials and describe their characteristics and applications |
identify types of flashings and describe their characteristics and applications |
identify types of anchors and describe their characteristics and applications |
identify types of membranes and describe their characteristics and applications |
identify types of sealants and describe their characteristics and applications |
describe requirements for separation of dissimilar materials |
identify location and placement of anchors for skylights and sloped glazing systems |
identify placement of purlins |
B-8.05.02L |
demonstrate knowledge of procedures used to install skylights, sloped glazing systems and their components |
identify tools and equipment used to install skylights, sloped glazing systems and their components, and describe their applications and procedures for use |
describe procedures used to install skylights, sloped glazing systems and their components |
B-8.05.03L |
demonstrate knowledge of regulatory requirements pertaining to skylights and sloped glazing systems |
interpret and identify codes and regulations pertaining to skylights and sloped glazing systems |
Range of variables
- components include: rafters, purlins, purlin bars/pressure caps, spigots, splice plates, pressure plates and caps, gutters, sleeve anchors
- types of skylights and sloped glazing systems include: ridge, hip, pyramid, barrel vault, T-bar, pressure cap, point-glazed
- types of weather seal materials include: tapes, sealants, flashings, gaskets
- types of flashings include: primary, secondary
- types of membranes include: EPDM rubber, self-adhered membrane
- requirements for separation of dissimilar materials include: shims, bituminous paint
- tools and equipment include: see Appendix B (Tools and Equipment)
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations
B-8.06 Installs entrance systems
B-8.06 Installs entrance systems
NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
NV |
yes |
NV |
NV |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
Reference Code |
Performance Criteria |
Evidence of Attainment |
B-8.06.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task and manufacturers’ specifications |
B-8.06.02P |
position entrance system |
entrance system is positioned according to layout |
B-8.06.03P |
plumb, level and square entrance system |
entrance system is plumbed, levelled and squared |
B-8.06.04P |
prepare frame for other trades to run electrical wiring through frame |
frame is prepared for installation of electrical wiring according to task, shop drawings and manufacturers’ specifications |
B-8.06.05P |
prepare and place components in rough opening |
components are prepared and placed in rough opening |
B-8.06.06P |
install components |
components are installed according to shop drawings |
Range of variables
- tools and equipment include: see Appendix B (Tools and Equipment)
- components include: handles, closers, thresholds, flush bolts, locksets, electric strikes, panic hardware (exit devices), pivots, restrictors
Knowledge
Reference Code |
Learning Outcomes |
Learning Objectives |
B-8.06.01L |
demonstrate knowledge of entrance systems, their components, characteristics and applications |
identify types of entrance systems and their components, and describe their characteristics and applications |
identify types of electronic hardware and describe their characteristics and applications |
B-8.06.02L |
demonstrate knowledge of procedures used to install entrance systems and their components |
identify tools and equipment used to install entrance systems and their components, and describe their applications and procedures for use |
describe procedures used to install entrance systems |
identify requirements to communicate and coordinate with other trades |
identify types of framing materials and describe their characteristics and applications |
B-8.06.03L |
demonstrate knowledge of regulatory requirements pertaining to installation of electrical wiring in entrance systems |
interpret and identify codes and regulations pertaining to installation of electrical wiring in entrance systems |
B-8.06.04L |
demonstrate knowledge of regulatory requirements pertaining to commercial window and door systems |
interpret and identify codes and regulations pertaining to commercial window and door systems |
Range of variables
- components include: handles, closers, thresholds, flush bolts, locksets, electric strikes, panic hardware (exit devices), pivots, restrictors
- types of entrance systems include: swing, bifold, revolving, sliding, portals, vestibule, TVS
- types of electronic hardware include: mag locks, handicap panels, card readers, key pad operators, automatic mats, auto sensors, shear locks, electric panic hardware, power transfers
- tools and equipment include: see Appendix B (Tools and Equipment)
- types of framing materials include: flush glaze, curtain wall with door adapter
- codes and regulations include: NBC, NECB, jurisdictional codes and regulations