Table of Contents
Task D-13 Installs resilient flooring
Task Descriptor
Installation of resilient flooring is the art of physically executing the design plans to achieve a durable and aesthetic result. Proper installation techniques are important to validate warranty and to improve longevity of the flooring system.
D-13.01 - Establishes layout and grid lines
D-13.01 - Establishes layout and grid lines
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-13.01.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-13.01.02P |
verify square layout |
square layout is verified by determining straight reference line and taking measurements |
| D-13.01.03P |
square material to room |
material is squared to room according to plans using layout methods |
| D-13.01.04P |
mark layout and grid lines |
layout and grid lines are marked using chalk line |
| D-13.01.05P |
adjust layout lines |
layout lines are adjusted to minimize use of small pieces of material along prominent walls and transitions |
Range of Variables
- tools and equipment include: chalk lines, measuring tapes, plumb bobs
- layout methods include: 3-4-5 method, laser levels, swinging arcs, equal distance
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-13.01.01L |
demonstrate knowledge of procedures to establish layout and grid lines |
identify tools and equipment used to establish layout and grid lines, and describe their procedures for use |
| interpret information pertaining to layout found on drawings and specifications |
| describe geometry and calculations used to perform layout and grid lines |
| describe procedures and methods to establish layout and grid lines |
| identify practices that reduce material waste |
Range of Variables
- tools and equipment include: chalk lines, measuring tapes, plumb bobs
D-13.02 - Installs resilient tiles
D-13.02 - Installs resilient tiles
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-13.02.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-13.02.02P |
locate placement of conductive grounding strips and position |
placement of conductive grounding strips and position for dissipating electrical current are located according to manufacturers’ specifications |
| D-13.02.03P |
apply adhesive |
adhesive is applied according to manufacturers’ recommendations |
| D-13.02.04P |
allow adhesive open time |
adhesive is allowed open time according to manufacturers’ recommendations |
| D-13.02.05P |
batch tiles |
tiles are batched to achieve even distribution of natural variations in tiles |
| D-13.02.06P |
lay tiles |
tiles are laid to maintain straight and square installation |
| D-13.02.07P |
cut tiles |
tiles are cut to fit around vertical obstructions using installation methods |
| D-13.02.08P |
prevent tile movement when using wet-set method |
tile movement is prevented when using wet-set method by working away from adhesive or using kneeling board |
| D-13.02.09P |
roll material |
material is rolled to improve adhesive transfer and bond according to manufacturers’ specifications |
Range of Variables
- tools and equipment include: tile cutters, utility knives, propane torches, heat guns, under-scribers, dividers
- manufacturers’ recommendations include: adhesive spread rate; method of adhesive application; open, working and curing times
- vertical obstructions include: walls, drains, door frames, electrical floor outlets, plumbing, electrical conduit
- installation methods include: pattern scribing, direct scribing, measuring
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-13.02.01L |
demonstrate knowledge of resilient tiles, their characteristics and applications |
identify types of resilient tiles, and describe their characteristics and applications |
| interpret information pertaining to resilient tiles found on drawings and specifications |
| describe acclimation requirements of resilient tiles |
| D-13.02.02L |
demonstrate knowledge of adhesives, their characteristics and applications |
identify types of adhesives, and describe their characteristics and applications |
| D-13.02.03L |
demonstrate knowledge of procedures to install resilient tiles and adhesives |
identify tools and equipment used to install resilient tiles and adhesives, and describe their procedures for use |
| identify hazards and describe safe work practices to install resilient tiles |
| describe procedures to apply adhesives to substrates |
| describe installation methods and procedures to cut resilient tiles |
| describe procedures to install resilient tiles |
| describe resilient tile installation patterns |
| describe procedures to roll resilient tiles |
| identify practices that reduce material waste |
Range of Variables
- characteristics include: grain, directional arrows
- types of resilient tiles include: pure vinyl, vinyl plank, luxury vinyl tile (LVT), linoleum, VCT, rubber, cork, static dissipative tile (SDT), conductive tile
- types of adhesives include: asphalt emulsion, clear set, conductive, polyurethane, two-part epoxy
- tools and equipment include: tile cutters, utility knives, propane torches, heat guns, under-scribers, dividers
- hazards include: burns, fumes, slips and falls, cutting hazards, lifting heavy materials
- installation methods include: pattern scribing, direct scribing, measuring
- installation patterns include: ashlar, basket weave, herringbone, brick, monolithic, quarter-turn, random
D-13.03 - Installs resilient sheet goods
D-13.03 - Installs resilient sheet goods
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-13.03.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-13.03.02P |
locate placement of conductive grounding strips and position |
placement of conductive grounding strips and position for dissipating electrical current are located according to manufacturers’ specifications |
| D-13.03.03P |
make relief cuts |
relief cuts are made according to dimensions and fixtures in installation area to prepare for adhesive |
| D-13.03.04P |
de-curl (massage) material ends |
material ends are de-curled (massaged) to ensure flatness of seams and edges according to manufacturers’ recommendations |
| D-13.03.05P |
lap and tube material |
material is lapped and tubed to accommodate ease of installation and working time of adhesives |
| D-13.03.06P |
apply adhesive and seam treatments |
adhesive and seam treatments are applied according to manufacturers’ specifications |
| D-13.03.07P |
roll material |
material is rolled to eliminate bubbles, and improve adhesive transfer and bond according to manufacturers’ specifications |
| D-13.03.08P |
cut material |
material is cut to fit vertical obstructions |
| D-13.03.09P |
roll perimeter and seams |
perimeter and seams are rolled with hand or seam roller to improve adhesive transfer and bond at edges |
Range of Variables
- tools and equipment include: utility knives, linoleum knives, seam rollers, notch blade knives, under scribers, bar scribers, dividers, linoleum carts, linoleum dollies, heat welding kits, edge trimmers, straightedges, squares
- vertical obstructions include: walls, drains, door frames, electrical floor outlets, plumbing, electrical conduit
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-13.03.01L |
demonstrate knowledge of resilient sheet goods, their characteristics and applications |
identify types of resilient sheet goods, and describe their characteristics and applications |
| interpret information pertaining to resilient sheet goods found on drawings and specifications |
| D-13.03.02L |
demonstrate knowledge of adhesives, their characteristics and applications |
identify types of adhesives, and describe their characteristics and applications |
| D-13.03.03L |
demonstrate knowledge of procedures to install resilient sheet goods and adhesives |
identify tools and equipment used to install resilient sheet goods and adhesives, and describe their procedures for use |
| identify hazards and describe safe work practices to install resilient sheet goods |
| describe procedures to apply adhesives to substrates |
| describe procedures to cut resilient sheet goods |
| describe strategic placement of material cuts and efficient use of material |
| describe procedures to install resilient sheet goods |
| describe procedures to roll resilient sheet goods |
| describe scribing methods |
| describe seam preparation |
| describe seaming methods |
| identify practices that reduce material waste |
Range of Variables
- types of resilient sheet goods include: PVC, rubber, linoleum, roto vinyl, conductive, inlaid vinyl
- characteristics include: heterogeneous, homogeneous
- types of adhesives include: conductive, polyurethane, two-part epoxy, acrylic, latex
- tools and equipment include: utility knives, linoleum knives, seam rollers, notch blade knives, under scribers, bar scribers, dividers, linoleum carts, linoleum dollies, heat welding kits, edge trimmers, straightedges, squares
- hazards include: dangerous fumes, slips and falls, cutting hazards, lifting heavy materials, burns
- scribing methods include: pattern scribing, 3-wall scribing, direct scribing
- seam preparation includes: edge trimming, pattern matching, overlapping
- seaming methods include: double cutting, pre-cutting, under scribing
D-13.04 - Cuts seams to fit
D-13.04 - Cuts seams to fit
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-13.04.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-13.04.02P |
trim edges of sheets |
edges of sheets are trimmed according to manufacturers’ specifications and recommended overlap |
| D-13.04.03P |
recess scribe seams |
seams are recess scribed to fit according to manufacturers’ specifications and industry practices |
| D-13.04.04P |
double cut seams |
seams are double cut according to manufacturers’ specifications and industry practices |
| D-13.04.05P |
straight edge cut and butt edges together |
seam is cut with straightedge and edges are butt together according to manufacturers’ specifications and industry practices |
Range of Variables
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, edge trimmers, straightedges, squares, seam rollers, dividers
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-13.04.01L |
demonstrate knowledge of procedures to cut seams to fit |
identify tools and equipment used to cut seams, and describe their procedures for use |
| describe procedures to cut seams to fit |
Range of Variables
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, edge trimmers, straightedges, squares, seam rollers, dividers
D-13.05 - Seals seams chemically
D-13.05 - Seals seams chemically
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-13.05.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-13.05.02P |
clean and prepare seam |
seam is cleaned and prepared using mineral spirits or recommended solvent to prevent contamination of seam sealer |
| D-13.05.03P |
mix seam sealer |
seam sealer is mixed according to manufacturers’ specifications |
| D-13.05.04P |
apply seam sealer |
seam sealer is applied according to manufacturers’ specifications |
| D-13.05.05P |
protect seams during drying time |
seams are protected during drying time using barriers to prevent contamination of seam sealer according to manufacturers’ specifications |
Range of Variables
- tools and equipment include: straightedges, rags, applicator bottles
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-13.05.01L |
demonstrate knowledge of seam sealers, their characteristics and applications |
identify types of seam sealers, and describe their characteristics and applications |
| interpret information pertaining to seam sealers found on manufacturers’ specifications |
| D-13.05.02L |
demonstrate knowledge of procedures to seal seams chemically |
identify tools and equipment used to seal seams chemically, and describe their procedures for use |
| describe procedures to clean and prepare seams |
| describe procedures to mix seam sealers |
| describe procedures to apply seam sealers |
Range of Variables
- tools and equipment include: straightedges, rags, applicator bottles
D-13.06 - Heat welds seams
D-13.06 - Heat welds seams
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-13.06.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-13.06.02P |
clean and prepare seam |
seam is cleaned and prepared to prevent contamination and weak bond |
| D-13.06.03P |
groove seams |
seams are grooved to depth and width according to product manufacturers’ specifications |
| D-13.06.04P |
set heat welder to temperature |
heat welder is set to temperature according to manufacturers’ specifications |
| D-13.06.05P |
apply weld rod |
weld rod is applied according to manufacturers’ specifications |
| D-13.06.06P |
trim weld rod |
weld rod is trimmed according to manufacturers’ specifications |
| D-13.06.07P |
perform final skiving |
final skiving is performed to achieve smooth and flat seam |
Range of Variables
- tools and equipment include: automatic welders, heat seam welding system (hand groover, heat welding gun, electric groover, nozzles for welder, trim plate, skiving tools, spatula knives, hobby knives, trimmers, cleaning tool)
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-13.06.01L |
demonstrate knowledge of flooring materials than can be heat welded |
identify types of flooring materials that can be heat welded |
| identify weld rods, and describe their characteristics and applications |
| D-13.06.02L |
demonstrate knowledge of procedures to heat weld seams |
identify tools and equipment used to heat weld seams, and describe their procedures for use |
| identify hazards and describe safe work practices to heat weld seams |
| describe procedures to clean and prepare seams |
| describe procedures to groove seams |
| identify grooving methods |
| describe procedures to heat weld seams |
| describe procedures to perform final skiving |
Range of Variables
- tools and equipment include: automatic welders, heat seam welding system (hand groover, heat welding gun, electric groover, nozzles for welder, trim plate, skiving tools, spatula knives, hobby knives, trimmers, cleaning tool)
- hazards include: burns, fumes
- grooving methods include: hand, machine
D-13.07 - Completes resilient flooring installation
D-13.07 - Completes resilient flooring installation
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-13.07.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-13.07.02P |
apply sealants around features and inside and outside doors |
sealants are applied around features and inside and outside doors according to project requirements and manufacturers’ specifications |
| D-13.07.03P |
perform final inspection and cleanup procedures |
final inspection and cleanup procedures are performed |
Range of Variables
- features include: bathtubs, water pipes, conduit, toe kicks
- cleanup procedures include: removing excess sealant and adhesive, removing debris
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-13.07.01L |
demonstrate knowledge of procedures to complete resilient flooring installation |
identify tools and equipment used to complete resilient flooring installation, and describe their procedures for use |
| identify hazards and describe safe work practices to complete resilient flooring installation |
| describe procedures to perform final inspection |
| describe cleanup procedures |
Range of Variables
- cleanup procedures include: removing excess sealant and adhesive, removing debris
Task D-14 Performs custom resilient flooring procedures
Task Descriptor
This task covers specialized installation procedures in the floorcovering trade such as coving, resilient flooring on stairs and specialty wall coverings. Some sheet good applications may cover wall as well as floors. These installations include residential, commercial and institutional applications.
D-14.01 - Performs coving operations
D-14.01 - Performs coving operations
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-14.01.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-14.01.02P |
cut, fit and fasten fillet/cove strips and capping |
fillet/cove strips and capping are cut, fit and fastened according to manufacturers’ specifications to support flooring material where floor meets wall and capping to receive material |
| D-14.01.03P |
install prefabricated coving |
prefabricated coving is installed according to manufacturers’ specifications |
| D-14.01.04P |
install v-plug corners and boot plug corners |
v-plug corners and boot plug corners are installed according to industry practices and manufacturers’ recommendations |
| D-14.01.05P |
heat material before bending |
material is heated before bending to prevent breakage and binding |
| D-14.01.06P |
ensure adhesion to cove strips |
adhesion to cove strips is ensured by pushing material into cove strips around perimeter of room |
| D-14.01.07P |
cut flooring material and fit into capping |
flooring material is cut and fit into capping |
| D-14.01.08P |
roll wall using seam roller |
wall is rolled using seam roller to improve glue transfer and bond |
| D-14.01.09P |
cut and fit inside and outside corners |
inside and outside corners are cut and fit using cutting methods |
Range of Variables
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, heat welding kits, edge trimmers, straightedges, squares, seam roller, material roller, compound miter saw, reverse scribers
- cutting methods include: pattern scribe, direct scribe, freehand knifing, pre-measure
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-14.01.01L |
demonstrate knowledge of coving, their characteristics and applications |
identify types of coving, and describe their characteristics and applications |
| D-14.01.02L |
demonstrate knowledge of adhesives, their characteristics and applications |
identify types of adhesives, and describe their characteristics and applications |
| D-14.01.03L |
demonstrate knowledge of procedures to perform coving procedures |
identify tools and equipment used to perform coving procedures, and describe their procedures for use |
| identify hazards and describe safe work practices to perform coving procedures |
| describe procedures to install coving |
Range of Variables
- types of coving include: pre-fabricated coving, on-site coving, V plug, boot plug
- types of adhesives include: contact tape, contact cement, nosing epoxy, base adhesives
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, heat welding kits, edge trimmers, straightedges, squares, seam roller, material roller, compound miter saw, reverse scribers
- hazards include: cutting hazards, burns, fire
D-14.02 - Installs tread, riser and stringer materials
D-14.02 - Installs tread, riser and stringer materials
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-14.02.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-14.02.02P |
measure and snap chalk line |
chalk line is measured and snapped to determine height of stringer material |
| D-14.02.03P |
scribe and fit stringers |
stringers are scribed and fit top to bottom |
| D-14.02.04P |
adhere stringer materials to wall surface and roll stringers |
stringer materials are adhered to wall surface and stringers are rolled to improve glue transfer and bond |
| D-14.02.05P |
cut, fit and scribe treads and risers |
treads and risers are cut, fit and scribed to ensure net finish |
| D-14.02.06P |
apply adhesive |
adhesive is applied according to manufacturers’ specifications and industry practices |
| D-14.02.07P |
roll tread and riser materials |
tread and riser materials are rolled |
| D-14.02.08P |
install tactile warning strips |
tactile warning strips are installed according to project requirements, manufacturers’ specifications and jurisdictional codes |
Range of Variables
- tools and equipment include: chalk lines, measuring tape, utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, edge trimmers, straightedges, squares, seam roller, material roller, compound miter saw, glue trowels, orbital sander, stair jig
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-14.02.01L |
demonstrate knowledge of treads, risers and stringer materials, their characteristics and applications |
identify types of treads, risers and stringer materials, and describe their characteristics and applications |
| D-14.02.02L |
demonstrate knowledge of types of adhesives, their characteristics and applications |
identify types of adhesives, and describe their characteristics and applications |
| D-14.02.03L |
demonstrate knowledge of procedures to install treads, risers and stringer materials |
identify tools and equipment used to install treads, risers and stringer materials, and describe their procedures for use |
| identify hazards and describe safe work practices to install treads, risers and stringer materials |
| describe procedures to install treads, risers and stringer materials |
| identify practices that reduce material waste |
| D-14.02.04L |
demonstrate knowledge of regulatory requirements pertaining to stairs |
identify codes, standards and regulations pertaining to stairs |
Range of Variables
- types of adhesives include: contact tape, contact cement, nosing epoxy, base adhesives, stair tread adhesive
- tools and equipment include: chalk lines, measuring tape, utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, edge trimmers, straightedges, squares, seam roller, material roller, compound miter saw, glue trowels, orbital sander, stair jig
- hazards include: dangerous fumes, falls, cutting hazards
D-14.03 - Installs resilient flooring on stairs
D-14.03 - Installs resilient flooring on stairs
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-14.03.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-14.03.02P |
cut, fit and fasten fillet/cove strips |
fillet/cove strips are cut, fit and fastened to receive and support flooring material where tread meets riser according to installation method and codes |
| D-14.03.03P |
fit flooring to riser, tread and stringer |
flooring is fit to riser, tread and stringer according to manufacturers’ specifications |
| D-14.03.04P |
cut and fit nosing |
nosing is cut and fit according to installation method |
| D-14.03.05P |
pattern match field, stairs and landings |
field, stairs and landings are pattern matched according to industry practices |
Range of Variables
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, heat welding kits, edge trimmers, straightedges, squares, tile cutter, material roller, hand roller, measuring tape
- installation methods include: one-piece, two-piece, coved
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-14.03.01L |
demonstrate knowledge of products used to install resilient flooring on stairs, their characteristics and applications |
identify types of products used to install resilient flooring on stairs, and describe their characteristics and applications |
| D-14.03.02L |
demonstrate knowledge of stairs, their characteristics, applications and construction |
identify stair substrates, and describe their characteristics and applications |
| identify types of stair construction, and describe their characteristics and applications |
| D-14.03.03L |
demonstrate knowledge of procedures to install resilient flooring on stairs |
identify tools and equipment used to install resilient flooring on stairs, and describe their procedures for use |
| identify hazards and describe safe work practices to install resilient flooring on stairs |
| describe installation method procedures, and sequence to install resilient flooring on stairs |
| identify practices that reduce material waste |
| D-14.03.04L |
demonstrate knowledge of regulatory requirements pertaining to stairs |
identify codes, standards and regulations pertaining to stairs |
Range of Variables
- resilient flooring includes: linoleum, sheet vinyl, VCT, rubber
- stair substrates include: wood, concrete, steel pan
- types of stair construction include: boxed, open-ended, double-ended, bullnose, spiral, curved, Hollywood, floating, winder
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, heat welding kits, edge trimmers, straightedges, squares, tile cutter, material roller, hand roller, measuring tape
- hazards include: dangerous fumes, falls, cutting hazards
- installation methods include: one-piece, two-piece, coved
D-14.04 - Installs insets, borders and feature strips
D-14.04 - Installs insets, borders and feature strips
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-14.04.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-14.04.02P |
scale measurements for insets, borders and feature strips from plans |
measurements are scaled for insets, borders and feature strips from plans to achieve scaled image |
| D-14.04.03P |
create geometric shapes |
geometric shapes are created according to job site requirements and drawings |
| D-14.04.04P |
place insets, borders and feature strips |
insets, borders and feature strips are placed according to design layout on drawings |
| D-14.04.05P |
incorporate pattern into field |
pattern is incorporated into field to achieve uniform look |
Range of Variables
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, heat welding kits, edge trimmers, straightedges, squares, tile cutter, material roller, hand roller, measuring tape
- geometric shapes include: circles, ellipses, curved lines
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-14.04.01L |
demonstrate knowledge of insets, borders and feature strips, their characteristics and applications |
identify types of insets, borders and feature strips, and describe their characteristics and applications |
| D-14.04.02L |
demonstrate knowledge of procedures to install insets, borders and feature strips |
identify tools and equipment used to install insets, borders and feature strips, and describe their procedures for use |
| identify hazards and describe safe work practices to install insets, borders and feature strips |
| describe procedures to install insets, borders and feature strips |
| identify geometric shapes created for installations |
| describe measurements taken to install insets, borders and feature strips |
| identify practices that reduce material waste |
Range of Variables
- tools and equipment include: utility knives, linoleum knives, notch blade knives, recess scribers, bar scribers, dividers, heat welding kits, edge trimmers, straightedges, squares, tile cutter, material roller, hand roller, measuring tape
- hazards include: dangerous fumes, falls, cutting hazards
- geometric shapes include: circles, ellipses, curved lines
D-14.05 - Installs specialty wall covering products
D-14.05 - Installs specialty wall covering products
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-14.05.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-14.05.02P |
cut specialty wall covering products |
specialty wall covering products are cut according to dimensions |
| D-14.05.03P |
bend and form material to inside and outside corners |
material is bent and formed to inside and outside corners according to wall dimensions and manufacturers’ specifications |
| D-14.05.04P |
apply and trowel adhesive |
adhesive is applied and troweled according to manufacturers’ specifications |
| D-14.05.05P |
roll wall surface |
wall surface is rolled to improve adhesive transfer and bond |
| D-14.05.06P |
seal seams |
seams are sealed using heat weld or H-strips |
Range of Variables
- tool and equipment include: jigsaws, hole saws, carbide blade knives, heat benders, laser lines, levels, circular saws, track saws, angle finder, measuring tape, plumb bob, material roller, hand roller, glue trowel, heat welding kit, step ladders
- specialty wall covering products include: sheet vinyl and panels, hygienic vinyl PVC rigid panels, wall protection
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-14.05.01L |
demonstrate knowledge of specialty wall covering products, their characteristics and applications |
identify types of specialty wall covering products, and describe their characteristics and applications |
| D-14.05.02L |
demonstrate knowledge of procedures to install specialty wall covering products |
identify tools and equipment used to install specialty wall covering products, and describe their procedures for use |
| identify hazards and describe safe work practices to install specialty wall covering products |
| describe procedures to install specialty wall covering products |
| describe procedures to apply and trowel adhesives |
| describe procedures to seal seams |
| identify practices that reduce material waste |
Range of Variables
- specialty wall covering products include: sheet vinyl and panels, hygienic vinyl PVC rigid panels, wall protection
- tool and equipment include: jigsaws, hole saws, carbide blade knives, heat benders, laser lines, levels, circular saws, track saws, angle finder, measuring tape, plumb bob, material roller, hand roller, glue trowel, heat welding kit, step ladders
- hazards include: falls, cutting hazards, burns, lifting heavy materials, body strains and pulls
Task D-15 Repairs resilient flooring and accessories
Task Descriptor
Floorcovering installers repair resilient flooring that is damaged and worn. This includes replacement of components and materials.
D-15.01 - Repairs resilient flooring
D-15.01 - Repairs resilient flooring
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-15.01.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-15.01.02P |
inspect substrate |
substrate is inspected to ensure it is ready to accept flooring repair |
| D-15.01.03P |
determine repair method |
repair method is determined |
| D-15.01.04P |
cut out damaged areas |
damaged areas are cut out according to manufacturers’ recommendations and industry practices |
| D-15.01.05P |
replace damaged areas |
damaged areas are replaced with best matching product |
| D-15.01.06P |
repair miscut, open, peaked and loose seams |
miscut, open, peaked and loose seams are repaired using manufacturer approved adhesive |
| D-15.01.07P |
protect seams during drying time of seam sealers |
seams are protected during drying time of seam sealers |
Range of Variables
- tools and equipment include: carpenter square, measuring tape, knives, heat gun, torches, adhesive trowel, patching tools, syringe, recess scriber, hand roller, heat welding kit
- repair methods include: patching, re-gluing and sealing seams, injecting adhesive, heat welding
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-15.01.01L |
demonstrate knowledge of resilient flooring, their characteristics, applications and construction |
identify types of resilient flooring, and describe their characteristics, applications and construction |
| D-15.01.02L |
demonstrate knowledge of procedures to repair resilient flooring |
identify tools and equipment used to repair resilient flooring, and describe their procedures for use |
| identify hazards and describe safe work practices to repair resilient flooring |
| describe repair methods and procedures to repair and replace resilient flooring |
| describe seaming methods |
| describe seam repair limitations |
| describe causes of damage to resilient flooring |
| identify practices that reduce material waste |
Range of Variables
- resilient flooring includes: linoleum, sheet vinyl, VCT, rubber
- tools and equipment include: carpenter square, measuring tape, knives, heat gun, torches, adhesive trowel, patching tools, syringe, recess scriber, hand roller, heat welding kit
- hazards include: cutting hazards, burns, slips and falls
- repair methods include: patching, re-gluing and sealing seams, injecting adhesive, heat welding
- seaming methods include: heat welding, chemical welding, tight scribe
- causes of damage include: moisture, contaminants, marks, wear and tear, damage during construction
D-15.02 - Repairs accessories
D-15.02 - Repairs accessories
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| NV |
yes |
NV |
NV |
NV |
yes |
NV |
ND |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| D-15.02.01P |
select and use tools and equipment |
tools and equipment are selected and used according to task |
| D-15.02.02P |
remove adhesives and fasteners |
adhesives and fasteners are removed from repair area to prevent damage and to salvage accessories for reinstallation |
| D-15.02.03P |
replace fasteners to complete repair |
fasteners are replaced to complete repair |
Range of Variables
- tools and equipment include: hammer, carpenter square, measuring tape, knives, heat gun, torches, adhesive trowel, patching tools, syringe, recess scriber, hand roller, stripping machine, pry bar
- accessories include: nosing, baseboards, capping, transitions
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| D-15.02.01L |
demonstrate knowledge of flooring accessories, their characteristics and applications |
identify types of flooring accessories, and describe their characteristics and applications |
| D-15.02.02L |
demonstrate knowledge of procedures to repair flooring accessories |
identify tools and equipment used to repair flooring accessories, and describe their procedures for use |
| identify hazards and describe safe work practices to repair flooring accessories |
| describe procedures to repair flooring accessories |
| identify practices that reduce material waste |
Range of Variables
- accessories include: nosing, baseboards, capping, transitions
- tools and equipment include: hammer, carpenter square, measuring tape, knives, heat gun, torches, adhesive trowel, patching tools, syringe, recess scriber, hand roller, stripping machine, pry bar
- hazards include: cutting hazards, burns, scrapes, slips and falls