Harmonization of Apprenticeship Training

Provincial and territorial apprenticeship authorities are each responsible for their respective apprenticeship programs. In the spirit of continual improvement, and to facilitate mobility among apprentices in Canada, participating authorities have agreed to work towards harmonizing certain aspects of their programs where possible. After consulting with their stakeholders in the trade, they have reached consensus on the following elements. Note that implementation of these elements may vary from jurisdiction to jurisdiction, depending on their own circumstances. For more information on the implementation in any province and territory, please contact that jurisdiction’s apprenticeship authority.

1. Trade name

The official Red Seal name for this trade is Concrete Finisher.

2. Number of Levels of Apprenticeship

The number of levels of technical training recommended for this trade is 2 (two).

3. Total Training Hours During Apprenticeship Training

The total hours of training, including both on-the-job and in-school training for this trade is 3600.

4. Sequencing Topics and Related Sub-tasks

The topic titles in the table below are placed in a column for each apprenticeship level for technical training. Each topic is accompanied by the sub-tasks and their reference number. The topics in the grey shaded cells represent those that are covered “in context” with other training in the subsequent years.

Sequencing Topics and Related Sub-tasks
Level 1 Level 2
  Safety-Related Functions in context
  Cures Concrete in context
  Protects Concrete in context
Safety-Related Functions
  • 1.01 Uses personal protective equipment (PPE) and safety equipment
  • 1.02 Maintains safe work environment
 
Tools and Equipment
  • 2.01 Uses hand tools
  • 2.03 Uses measuring equipment
Tools and Equipment
  • 2.02 Uses power tools
  • 2.03 Uses measuring equipment
Organizes Work
  • 3.01 Uses documentation
  • 3.02 Determines material requirements and quantities
  • 3.03 Sequences work procedures
Organizes Work
  • 3.01 Uses documentation
  • 3.02 Determines material requirements and quantities
  • 3.03 Sequences work procedures
Communication
  • 4.01 Uses communication techniques
Communication and Mentoring
  • 4.01 Uses communication techniques
  • 4.02 Uses mentoring techniques
Prepares Site
  • 5.01 Inspects site
  • 5.02 Prepares sub-grade and elevations
Prepares Site
  • 5.01 Inspects site
  • 5.02 Prepares sub-grade and elevations
Formwork
  • 6.01 Constructs concrete formwork
  • 6.02 Installs reinforcement
  • 6.03 Inspects formwork and reinforcements
  • 6.04 Installs construction, isolation and expansion joints
  • 6.05 Removes forms
Formwork
  • 6.01 Constructs concrete formwork
  • 6.02 Installs reinforcement
  • 6.03 Inspects formwork and reinforcements
  • 6.05 Removes forms
Places Concrete
  • 7.01 Transports concrete onsite
  • 7.02 Spreads concrete
  • 7.03 Consolidates concrete
Places Concrete
  • 7.01 Transports concrete
  • 7.03 Consolidates concrete
Levels Concrete
  • 8.01 Establishes elevation
  • 8.02 Screeds concrete
  • 8.03 Bull floats concrete
Levels Concrete
  • 8.01 Establishes elevation
  • 8.02 Screeds concrete
Floats Concrete
  • 9.01 Floats concrete by hand
Floats Concrete
  • 9.02 Floats concrete by machine
Hand-tools Concrete
  • 10.01 Edges perimeter of slab
  • 10.03 Tools contraction joints
Hand-tools Concrete
  • 10.02 Finishes extruded concrete surfaces
Trowels Concrete
  • 11.01 Trowels concrete by hand
Trowels Concrete
  • 11.02 Trowels concrete by machine
  Applies Surface Treatment (Plastic)
  • 12.01 Applies dry-shake aggregate surface hardeners
  • 12.02 Applies exposed aggregate finish
  • 12.03 Textures concrete surface
  • 12.04 Applies stamped concrete surface finish
  • 12.05 Applies evaporation reducers
Cures Concrete
  • 13.01 Wet-cures concrete
  • 13.02 Chemical cures concrete
 
Creates Contraction Joints
  • 14.01 Saw cuts contraction joints
  • 14.02 Fills joints
 
Protects Concrete
  • 15.01 Protects plastic concrete
  • 15.02 Protect hardened concrete
 
Repairs Concrete
  • 16.01 Inspects concrete
  • 16.02 Removes materials
  • 16.03 Prepares surface for repair and restoration
  • 16.04 Installs repair materials
Repairs and Restores Concrete
  • 16.01 Inspects concrete
  • 16.02 Removes materials
  • 16.03 Prepares surface for repair and restoration
  • 16.04 Installs repair materials
  Applies Surface Treatment (Hardened Concrete)
  • 17.01 Prepares surface for surface treatments
  • 17.02 Abrades surface to achieve architectural finish
  • 17.03 Applies seamless systems
  • 17.04 Applies bonded and non-bonded toppings to concrete
  • 17.05 Parges vertical surfaces
  • 17.06 Applies chemical surface treatment
  Grouts
  • 18.01 Prepares surface for grouting
  • 18.02 Mixes grout
  • 18.03 Installs grout
  • 18.04 Finishes exposed grout surfaces
  Cutting and Coring
  • 19.01 Performs cutting
  • 19.02 Performs coring