Table of Contents
Task F-13 Loads and unloads components for transport
Task descriptor
The crane and components need to be selected for the job and then loaded or driven onto trailers for transport to the jobsite to then be unloaded for assembly.
F-13.01-Loads crane and components
F-13.01-Loads crane and components
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-13.01.01P |
identify and select crane components to be loaded |
crane components to be loaded are identified and selected according to required configuration of crane |
| F-13.01.02P |
identify and select trailers to be loaded |
trailers to be loaded are identified and selected according to weights and dimensions of components |
| F-13.01.03P |
select assist crane |
assist crane is selected according to weights and radius of components being loaded |
| F-13.01.04P |
determine lifting points |
lifting points are determined according to manufacturers’ specifications |
| F-13.01.05P |
determine sequence of loading crane components |
sequence of loading crane components is determined according to weights and dimensions |
| F-13.01.06P |
direct assist crane operator and crew for crane component placement |
assist crane operator and crew are directed for crane component placement |
| F-13.01.07P |
remove components from crane |
components are removed from crane to satisfy jurisdictional weight and dimension requirements for transport |
| F-13.01.08P |
distribute crane and component weight on transport equipment |
crane and component weight on transport equipment are distributed according to jurisdictional regulations |
| F-13.01.09P |
secure crane and components on transport equipment |
crane and components are secured on transport equipment according to jurisdictional regulations |
| F-13.01.10P |
drive crane onto transport equipment considering factors |
crane is driven onto transport equipment considering factors |
| F-13.01.11P |
confirm all crane components have been loaded |
all crane components have been loaded |
Range of variables
- components include: superstructure, carrier/car body, outriggers, crawler tracks, booms, jibs, counterweights, job boxes, mats, hook blocks, overhaul ball, pendant lines, hoist ropes
- transport equipment includes: flatbeds, lowbeds, floating platforms, rail cars, boom launcher trailer
- jurisdictional regulations include: highway legislation, road regulations, National Safety Code (NSC)
- factors include: type of crane, type of transport equipment, site conditions
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-13.01.01L |
demonstrate knowledge of mobile cranes, their characteristics and applications |
define terminology associated with mobile cranes |
| identify hazards and describe safe work practices pertaining to mobile cranes |
| identify types of mobile cranes and describe their characteristics and applications |
| identify types of engines in mobile cranes and describe their characteristics and applications |
| identify crane components and describe their characteristics and applications |
| F-13.01.02L |
demonstrate knowledge of procedures used to load cranes and components for transport |
define terminology associated with crane transportation |
| identify hazards and describe safe work practices pertaining to loading cranes and components |
| interpret charts, drawings and specifications relating to crane transportation |
| identify tools and equipment used to load cranes and describe their applications and procedures for use |
| identify requirements and describe procedures used to prepare cranes for transport |
| describe procedures used to load cranes and components for transport travel |
| identify types of rigging equipment used to load cranes and components, and describe their characteristics and applications |
| identify types of tie downs used to load cranes and components, and describe their characteristics and applications |
| identify types of transport equipment used to transport cranes and components, and describe their characteristics and applications |
| describe placement procedures used to avoid damage |
| describe loading sequence for transportation |
| F-13.01.03L |
demonstrate knowledge of regulatory requirements pertaining to crane transportation |
identify codes, standards and regulations pertaining to crane transportation |
Range of variables
- types of mobile cranes include: hydraulic and lattice boom (truck mounted, all-terrain [AT], rough-terrain [RT], crawler)
- types of engines in mobile cranes include: gas, diesel, propane
- components include: superstructure, carrier/car body, outriggers, crawler tracks, booms, jibs, counterweights, job boxes, mats, hook blocks, overhaul ball, pendant lines, hoist ropes
- types of rigging equipment include: synthetic, wire rope slings, chain slings, shackles, hooks
- types of tie downs include: chains, cables, turnbuckles, synthetic belts, binders
- transport equipment includes: flatbeds, lowbeds, floating platforms, rail cars, boom launcher trailer
F-13.02-Unloads crane and components
F-13.02-Unloads crane and components
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-13.02.01P |
identify and select sequence of trailers to be unloaded |
sequence of trailers to be unloaded is identified and selected |
| F-13.02.02P |
confirm all components have been delivered and have not been damaged in transport |
all components have been delivered and were not damaged in transport |
| F-13.02.03P |
select assist crane |
assist crane is selected according to weights and radius of load |
| F-13.02.04P |
determine lifting points |
lifting points are determined according to manufacturers’ specifications |
| F-13.02.05P |
determine sequence of crane components to be unloaded |
sequence of crane components to be unloaded is determined |
| F-13.02.06P |
identify location to assemble crane |
location to assemble crane is identified |
| F-13.02.07P |
unlash crane and components on transport equipment |
crane and components on transport equipment are unlashed |
| F-13.02.08P |
drive crane off transport equipment considering factors |
crane is driven off transport equipment considering factors |
| F-13.02.09P |
direct assist crane operator and crew for crane component unloading |
assist crane operator and crew are directed for crane component unloading |
Range of variables
- components include: superstructure, carrier/car body, outriggers, crawler tracks, booms, jibs, counterweights, job boxes, mats, hook blocks, overhaul ball, pendant lines, hoist ropes
- transport equipment includes: flatbeds, lowbeds, floating platforms, rail cars, boom launcher trailer
- factors include: type of crane, type of transport equipment, site conditions
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-13.02.01L |
demonstrate knowledge of procedures used to unload cranes and components after transport |
define terminology associated with crane and components and their transportation |
| identify hazards and describe safe work practices pertaining to unloading cranes and components |
| interpret charts, drawings and specifications relating to crane transportation |
| identify tools and equipment used to unload cranes and describe their applications and procedures for use |
| describe procedures used to unload cranes and components |
| describe removal sequence for assembly |
| describe blocking procedures to prevent injury and equipment damage |
| describe site preparation procedures |
| identify types of transport equipment used to transport cranes and components, and describe their characteristics and applications |
| F-13.02.02L |
demonstrate knowledge of regulatory requirements pertaining to crane transportation |
identify codes, standards and regulations pertaining to crane transportation |
Range of variables
- components include: superstructure, carrier/car body, outriggers, crawler tracks, booms, jibs, counterweights, job boxes, mats, hook blocks, overhaul ball, pendant lines, hoist ropes
- site preparation procedures include: adequate space, traffic control, permits, allowable ground-bearing pressure
- transport equipment includes: flatbeds, lowbeds, floating platforms, rail cars, boom launcher trailer
Task F-14 Drives cranes on public roadways
Task descriptor
Cranes are self-propelled for driving on public roadways. Disassembly of some cranes may be necessary to comply with jurisdictional regulations.
Pre‑trip planning is necessary and it includes confirming roles and responsibilities of crew members that will be participating in the transport and organizing escort vehicles.
F-14.01-Performs pre-trip planning
F-14.01-Performs pre-trip planning
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-14.01.01P |
confirm application for permit has been made |
application for permit has been made |
| F-14.01.02P |
interpret permits and confirm route |
permits are interpreted and route is confirmed considering factors |
| F-14.01.03P |
verify route |
route is verified using map tools |
| F-14.01.04P |
confirm crane is ready for transport |
crane is ready for transport considering factors |
| F-14.01.05P |
schedule and confirm time of transport |
time of transport is scheduled and confirmed |
Range of variables
- factors (route) include: jurisdictional regulations, travel times, lanes of traffic, rush hours, road conditions (grades, terrain, ice, mud), bridge capacities, clearances, load types, turning radius for boom dollies, boom tip and superstructures
- map tools include: internet, global positioning system (GPS), printed map
- factors (crane ready for transport) include: licensing, registration, insurance, permits
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-14.01.01L |
demonstrate knowledge of procedures used to perform pre-trip planning |
identify factors for selecting transportation routes |
| interpret charts, drawings and specifications relating to crane transportation |
| identify types of map tools used for pre-trip planning, and describe their characteristics and applications |
| F-14.01.02L |
demonstrate knowledge of regulatory requirements pertaining to crane transportation |
identify codes, standards, restrictions and regulations pertaining to crane transportation |
Range of variables
- factors (route) include: jurisdictional regulations, travel times, lanes of traffic, rush hours, road conditions (grades, terrain, ice, mud), bridge capacities, clearances, load types, turning radius for boom dollies, boom tip and superstructures
- specifications include: travel mode, weights and dimensions
- map tools include: internet, GPS, printed map
- restrictions and regulations include: weight, height, width and requirement for escort vehicles, hours of service
F-14.02-Prepares crane for transport
F-14.02-Prepares crane for transport
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-14.02.01P |
remove components |
components are removed according to jurisdictional regulations |
| F-14.02.02P |
install boom in boom dolly or remove boom from crane |
boom in boom dolly is installed or boom is removed from crane |
| F-14.02.03P |
set crane to travel mode |
crane is set to travel mode |
| F-14.02.04P |
verify safety equipment |
safety equipment is verified |
| F-14.02.05P |
perform pre-trip inspection and complete required documentation |
pre-trip inspection is performed and required documentation is completed according to company policies and jurisdictional regulations |
Range of variables
- jurisdictional regulations include: NSC, weights and dimensions
- travel mode includes: steering, boom float, suspension adjustments, swing brake requirements
- safety equipment includes: road flares, fire extinguishers, reflectors
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-14.02.01L |
demonstrate knowledge of procedures used to prepare cranes for transport |
define terminology associated with crane transportation |
| identify hazards and describe safe work practices pertaining to crane transportation |
| interpret charts, drawings and specifications relating to crane transportation |
| identify tools and equipment used for crane transportation and describe their applications and procedures for use |
| describe procedures used to perform pre-trip inspection and complete required documentation |
| describe procedures used to remove components |
| F-14.02.02L |
demonstrate knowledge of regulatory requirements pertaining to crane transportation |
identify codes, standards, jurisdictional regulations pertaining to crane transportation |
Range of variables
- jurisdictional regulations include: NSC, weights and dimensions
F-14.03-Drives cranes
F-14.03-Drives cranes
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-14.03.01P |
navigate roads |
roads are navigated considering factors according to jurisdictional regulations |
| F-14.03.02P |
obey driving regulations and manufacturers’ instructions |
driving regulations and manufacturers’ instructions are obeyed while driving crane |
Range of variables
- factors include: weights and dimensions, crane size, road width, bridge weight, overpass height restrictions, weather conditions, driving conditions
- jurisdictional regulations include: NSC, weights and dimensions
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-14.03.01L |
demonstrate knowledge of procedures used to drive cranes |
define terminology associated with crane transportation |
| identify hazards and describe safe work practices pertaining to driving cranes |
| interpret charts, drawings and specifications relating to driving cranes |
| F-14.03.02L |
demonstrate knowledge of regulatory requirements pertaining to crane transportation |
identify codes, standards, jurisdictional regulations pertaining to crane transportation |
Range of variables
- jurisdictional regulations include: NSC, weights and dimensions
Task F-15 Assembles and disassembles lattice boom cranes
Task descriptor
Mobile crane operators need to disassemble cranes in order to transport them to and from jobsites. Disassembly of the crane may be necessary to comply with jurisdictional road regulations. Mobile crane operators assemble the cranes once on site.
F-15.01-Installs tracks on car body (lattice boom)
F-15.01-Installs tracks on car body (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.01.01P |
check that car body is level |
car body is levelled |
| F-15.01.02P |
remove blocking and safety chains between drive sprockets and pads |
blocking and safety chains between drive sprockets and pads are removed |
| F-15.01.03P |
extend/retract tracks |
tracks are extended/retracted according manufacturers’ specifications and instructions |
| F-15.01.04P |
position track onto car body |
track is positioned onto car body using auxiliary lift equipment or manufacturers’ specifications and instructions for self-assembly |
| F-15.01.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions to secure track on car body |
| F-15.01.06P |
join hydraulic/mechanical connections |
hydraulic/mechanical connections are joined according to manufacturers’ specifications and instructions to complete drive/outrigger circuits |
| F-15.01.07P |
adjust track and chain tension |
track and chain tension is adjusted according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.01.01L |
demonstrate knowledge of lattice boom cranes, their components, characteristics and applications |
define terminology associated with lattice boom cranes and their components |
| identify lattice boom crane components requiring assembly |
| F-15.01.02L |
demonstrate knowledge of procedures used to install tracks on car body of lattice boom cranes |
identify tools and equipment used to install tracks on car body of lattice boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of tracks on car body of lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of tracks on car body of lattice boom cranes |
| describe procedures used to install tracks on car body of lattice boom cranes |
| describe capabilities and limitations of auxiliary lift equipment |
| identify types of fasteners used in installation of tracks on car body of lattice boom cranes |
| F-15.01.03L |
demonstrate knowledge of regulatory requirements pertaining to assembly of lattice boom cranes |
identify codes, standards and regulations pertaining to assembly of lattice boom cranes |
Range of variables
- components include: tracks, car body, carrier, superstructure/upperworks, outrigger boxes, boom base, boom and jib, counterweights, hoist ropes, hook blocks, overhaul balls, gantry, A-frame, mast, inner and outer bail, boom back stop, boom tip
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes
- fasteners include: bolts, pins and keepers, wedges
F-15.02-Installs superstructure/upperworks (lattice boom)
F-15.02-Installs superstructure/upperworks (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.02.01P |
inspect for defects |
defects are inspected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-15.02.02P |
support with blocking suitable for ground conditions and level crane |
crane is supported with blocking suitable for ground conditions and levelled using equipment to facilitate removal of superstructure/upperworks |
| F-15.02.03P |
clean surfaces and apply lubricant to pins and connection points |
surfaces are cleaned and lubricant is applied to pins and connection points according to manufacturers’ specifications and instructions to allow assembly |
| F-15.02.04P |
position superstructure/upperworks onto car body/carrier |
superstructure/upperworks is positioned onto car body/carrier according to manufacturers’ specifications and instructions |
| F-15.02.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions to secure superstructure/upperworks on car body/carrier |
| F-15.02.06P |
connect hydraulic lines and electrical connections |
hydraulic lines and electrical connections are connected according to manufacturers’ specifications and instructions to complete circuits |
Range of variables
- defects include: worn bolts, pins and bushings
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
- equipment includes: jacks, assist cranes
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.02.01L |
demonstrate knowledge of procedures used to install superstructure/upperworks on lattice boom cranes |
identify tools and equipment used to install superstructure/upperworks on lattice boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of superstructure/upperworks on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of superstructure/upperworks on lattice boom cranes |
| identify types of possible defects found in superstructure/upperworks on lattice boom cranes |
| describe procedures used to install superstructure/upperworks on lattice boom cranes |
| identify types of fasteners used in installation of superstructure/upperworks on lattice boom cranes |
| describe hydraulic and electrical connections required to attach superstructure/upperworks onto car body/carrier |
| F-15.02.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of lattice boom cranes |
identify codes, standards and regulations pertaining to assembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: worn bolts, pins and bushings
- fasteners include: bolts, pins and keepers, wedges
F-15.03-Installs outrigger boxes (lattice boom)
F-15.03-Installs outrigger boxes (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.03.01P |
position and secure outrigger box |
outrigger box is positioned and secured according to manufacturers’ specifications and instructions |
| F-15.03.02P |
inspect for defects |
defects are inspected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-15.03.03P |
clean fittings |
fittings are cleaned to avoid oil contamination and ensure ease of installation |
| F-15.03.04P |
connect hoses and electrical wiring |
hoses and electrical wiring are connected according to manufacturers’ specifications and instructions |
| F-15.03.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged hoses, fittings and cylinders; corrosion; cracks
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.03.01L |
demonstrate knowledge of procedures used to install outrigger boxes on lattice boom cranes |
identify tools and equipment used to install outrigger boxes on lattice boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of outrigger boxes on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of outrigger boxes on lattice boom cranes |
| identify types of possible defects in outrigger boxes on lattice boom cranes |
| describe procedures used to install outrigger boxes on lattice boom cranes |
| identify types of fasteners used in installation of outrigger boxes on lattice boom cranes |
| describe hydraulic and electrical connections required to attach outrigger boxes to lattice boom cranes |
| describe capabilities and limitations of self-erecting procedures |
| F-15.03.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of lattice boom cranes |
identify codes, standards and regulations pertaining to assembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged hoses, fittings and cylinders; corrosion; cracks
- fasteners include: bolts, pins and keepers, wedges
F-15.04-Installs boom base (lattice boom)
F-15.04-Installs boom base (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.04.01P |
clean and lubricate pins and bushings |
pins and bushings are cleaned and lubricated according to manufacturers’ specifications and instructions to allow assembly |
| F-15.04.02P |
inspect for defects |
defects are detected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-15.04.03P |
raise gantry, A-frame or live mast to working position |
gantry, A-frame or live mast are raised to working position according to manufacturers’ specifications and instructions |
| F-15.04.04P |
position and secure boom base onto superstructure/upperworks |
boom base is positioned onto superstructure/upperworks using assist crane or self-installation and secured according to manufacturers’ specifications and instructions |
| F-15.04.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions |
| F-15.04.06P |
connect hoses and electrical wiring |
hoses and electrical wiring are connected according to manufacturers’ specifications and instructions to complete circuits |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged hoses, fittings and cylinders; cracks; corrosion; dents
- fasteners include: heel pins, keeper pins, bridle connections, bolts
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.04.01L |
demonstrate knowledge of procedures used to install boom bases on lattice boom cranes |
identify tools and equipment used to install boom bases on lattice boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of boom bases on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of boom bases on lattice boom cranes |
| identify types of possible defects in boom bases on lattice boom cranes |
| describe procedures used to install boom bases on lattice boom cranes |
| identify types of fasteners used in installation of boom bases on superstructure/upperworks |
| describe hydraulic and electrical connections required to attach boom bases to superstructure/upperworks |
| F-15.04.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of lattice boom cranes |
identify codes, standards and regulations pertaining to assembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged hoses, fittings and cylinders; cracks; corrosion; dents
- fasteners include: heel pins, keeper pins, bridle connections, bolts
F-15.05-Installs counterweights (lattice boom)
F-15.05-Installs counterweights (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.05.01P |
inspect for defects |
defects are inspected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-15.05.02P |
determine installation sequence and placement of counterweights |
installation sequence and placement of counterweights are determined according to manufacturers’ specifications and instructions |
| F-15.05.03P |
place counterweights on crane (tray or base plate) |
counterweights on crane (tray or base plate) are placed according to manufacturers’ specifications and instructions |
| F-15.05.04P |
raise and lower assembled counterweights into position |
assembled counterweights are raised and lowered into position according to manufacturers’ specifications and instructions |
| F-15.05.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions to secure assembled counterweights |
Range of variables
- defects include: broken bolts, damaged threads and pins, cracks, broken lifting lugs or eyes
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins, bolts, stack, cylinders, chains
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.05.01L |
demonstrate knowledge of procedures used to install counterweights on lattice boom cranes |
identify tools and equipment used to install counterweights on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of counterweights on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of counterweights on lattice boom cranes |
| identify types of possible defects in counterweights on lattice boom cranes |
| describe procedures used to determine sequence and placement of counterweights on lattice boom cranes |
| identify types of fasteners used in installation of counterweights |
| F-15.05.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of lattice boom cranes |
identify codes, standards and regulations pertaining to assembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: broken bolts, damaged threads and pins, cracks, broken lifting lugs or eyes
- fasteners include: pins, bolts, stack, cylinders, chains
F-15.06-Assembles main boom, tip and boom attachments (lattice boom)
F-15.06-Assembles main boom, tip and boom attachments (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.06.01P |
inspect for defects |
defects are inspected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-15.06.02P |
determine installation sequence of main boom, tip and jib sections |
installation sequence of main boom, tip and jib sections is determined according to manufacturers’ specifications and instructions |
| F-15.06.03P |
use blocking to suit ground conditions |
blocking is used to suit ground conditions |
| F-15.06.04P |
lay out and connect main boom, tip and jib sections (including boom components and wiring) |
main boom, tip and jib sections (including boom components and wiring) are laid out and connected according to manufacturers’ specifications and instructions |
| F-15.06.05P |
configure boom and boom attachments |
boom and boom attachments are configured according to manufacturers’ specifications and instructions |
Range of variables
- defects include: damaged chords, lacings, pendants, sheaves, pins and bushings; corrosion
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
- boom components include: pendant (steel/cable), walkway, sheaves, boom sections, load cells, boom angle sensors, limit switches
- boom attachments include: auxiliary, jibs (luffing, fixed), masts, reeving, mid-fall, pile drive, grab bucket
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.06.01L |
demonstrate knowledge of procedures used to assemble main boom, tip, and their components and attachments on lattice boom cranes |
identify tools and equipment used to assemble main boom and tip, and their components and attachments on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to assembly of main boom and tip, and their components and attachments on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to assembly of boom and tip, and their components and attachments on lattice boom cranes |
| identify types of possible defects in boom and tip, and their components and attachments on lattice boom cranes |
| describe procedures used to determine sequence, lay out and installation of main boom and tip, and their components and attachments on lattice boom cranes |
| describe procedures used to determine blocking required based on ground conditions |
| describe procedures used to configure boom and boom attachments |
| F-15.06.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of lattice boom cranes |
identify codes, standards and regulations pertaining to assembly of lattice boom cranes |
Range of variables
- boom components include: pendant (steel/cable), walkway, sheaves, boom sections, load cells, boom angle sensors, limit switches
- boom attachments include: auxiliary, jibs (luffing, fixed), masts, reeving, mid-fall, pile drive, grab bucket
- hazards include: pinch points, falling hazards, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged chords, lacings, pendants, sheaves, pins and bushings; corrosion
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
F-15.07-Installs hook blocks and overhaul ball (lattice boom)
F-15.07-Installs hook blocks and overhaul ball (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.07.01P |
determine required block or ball overhaul weight |
required block or ball overhaul weight is determined to match boom length and reeving |
| F-15.07.02P |
inspect hook block and overhaul ball for size and WLL |
hook block and overhaul ball are inspected for size and WLL according to manufacturers’ specifications and instructions |
| F-15.07.03P |
spool out stored hoist rope off of winch |
stored hoist rope is spooled out off of winch according to manufacturers’ specifications and instructions |
| F-15.07.04P |
cut and seize hoist rope if required |
hoist rope is cut and seized if required using cable cutting equipment according to manufacturers’ specifications and instructions |
| F-15.07.05P |
reeve hook block with required parts of hoist rope to lift calculated weight |
hook block is reeved with required parts of hoist rope according to manufacturers’ specifications and instructions to lift calculated weight |
| F-15.07.06P |
terminate hoist rope ends |
hoist rope ends are terminated according to manufacturers’ specifications and instructions using connections |
| F-15.07.07P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- connections include: wedge sockets, button sockets
- fasteners include: pins and keepers, wire rope clips
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.07.01L |
demonstrate knowledge of procedures used to install hook blocks and overhaul ball on lattice boom cranes |
identify tools and equipment used to install hook blocks and overhaul ball on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of hook blocks and overhaul ball on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of hook blocks and overhaul ball on lattice boom cranes |
| describe procedures used to install hook blocks and overhaul ball on lattice boom cranes |
| identify types of fasteners used in installation of hook blocks and overhaul ball on lattice boom cranes |
| F-15.07.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of lattice boom cranes |
identify codes, standards and regulations pertaining to assembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads, broken wires, entanglement, stored energy
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers, wire rope clips
F-15.08-Removes hook blocks and overhaul ball (lattice boom)
F-15.08-Removes hook blocks and overhaul ball (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.08.01P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-15.08.02P |
dismantle connections |
connections are dismantled according to manufacturers’ specifications and instructions |
| F-15.08.03P |
remove hoist rope from hook block |
hoist rope is removed from hook block according to manufacturers’ specifications and instructions |
| F-15.08.04P |
spool hoist rope onto winch |
hoist rope is spooled onto winch according to manufacturers’ specifications and instructions |
| F-15.08.05P |
secure hoist rope on drum |
hoist rope is secured on drum according to industry standards to preserve spooling |
Range of variables
- fasteners include: pins and keepers, wire rope clips
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- connections include: wedge sockets, button sockets
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.08.01L |
demonstrate knowledge of procedures used to remove hook blocks and overhaul ball on lattice boom cranes |
identify tools and equipment used to remove hook blocks and overhaul ball on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of wire ropes, hook blocks and overhaul ball on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of hook blocks and overhaul ball on lattice boom cranes |
| describe procedures used to remove hook blocks and overhaul ball on lattice boom cranes |
| identify types of fasteners used with hook blocks and overhaul ball on lattice boom cranes |
| F-15.08.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of lattice boom cranes |
identify codes, standards and regulations pertaining to disassembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads, broken wires, entanglement, stored energy
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers, wire rope clips
F-15.09-Disassembles main boom, tip and boom attachments (lattice boom)
F-15.09-Disassembles main boom, tip and boom attachments (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.09.01P |
lower main boom, tip and boom attachments onto blocking suitable for ground conditions |
main boom, tip and boom attachments are lowered onto blocking suitable for ground conditions |
| F-15.09.02P |
dismantle main boom, tip and boom attachment sections (including boom components and wiring) |
main boom, tip and boom attachment sections (including boom components and wiring) are dismantled according to manufacturers’ specifications and instructions |
| F-15.09.03P |
remove and store fasteners and boom components |
fasteners and boom components are removed and stored according to manufacturers’ specifications and instructions |
Range of variables
- boom attachments include: auxiliary, jibs (luffing, fixed), masts, reeving, mid-fall, pile drive, grab bucket
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
- boom components include: pendant (steel/cable), walkway, sheaves
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers, wire rope clips
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.09.01L |
demonstrate knowledge of procedures used to disassemble main boom, tip and their components and attachments on lattice boom cranes |
identify tools and equipment used to disassemble main boom, tip and their components and attachments on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to disassembly of main boom, tip and their components and attachments on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to disassembly of main boom, tip and their components and attachments on lattice boom cranes |
| describe procedures used to disassemble main boom, tip and their components and attachments on lattice boom cranes |
| describe procedures used to determine blocking required based on ground conditions |
| F-15.09.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of lattice boom cranes |
identify codes, standards and regulations pertaining to disassembly of lattice boom cranes |
Range of variables
- boom components include: pendant (steel/cable), walkway, sheaves
- boom attachments include: auxiliary, jibs (luffing, fixed), masts, reeving, mid-fall, pile drive, grab bucket
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
F-15.10-Removes counterweights (lattice boom)
F-15.10-Removes counterweights (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.10.01P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-15.10.02P |
raise and lower counterweight assembly out of position |
counterweight assembly is raised and lowered out of position according to manufacturers’ specifications and instructions |
| F-15.10.03P |
disassemble counterweight assembly |
counterweight assembly is disassembled according to manufacturers’ specifications and instructions |
Range of variables
- fasteners include: pins, bolts, stack, cylinders, chains
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.10.01L |
demonstrate knowledge of procedures used to remove counterweights on lattice boom cranes |
identify tools and equipment used to remove counterweights on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of counterweights on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of counterweights on lattice boom cranes |
| describe procedures used to remove counterweights on lattice boom cranes |
| F-15.10.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of lattice boom cranes |
identify codes, standards and regulations pertaining to disassembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
F-15.11-Removes boom base (lattice boom)
F-15.11-Removes boom base (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.11.01P |
disconnect hoses and electrical wiring |
hoses and electrical wiring are disconnected according to manufacturers’ specifications and instructions |
| F-15.11.02P |
support base |
base is supported according to manufacturers’ specifications and instructions |
| F-15.11.03P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-15.11.04P |
lift boom base off superstructure/upperworks |
boom base is lifted off superstructure/upperworks according to manufacturers’ specifications and instructions |
| F-15.11.05P |
lower gantry, A-frame and live mast to stowed position |
gantry, A-frame and live mast are lowered to stowed position according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: heel pins, keeper pins, bridle connections, bolts
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.11.01L |
demonstrate knowledge of procedures used to remove boom base from lattice boom cranes |
identify tools and equipment used to remove boom base from lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of boom base from lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of boom base from lattice boom cranes |
| describe procedures used to remove boom base from lattice boom cranes |
| F-15.11.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of lattice boom cranes |
identify codes, standards and regulations pertaining to disassembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure, stored energy (hydraulic or mechanical)
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
F-15.12-Removes superstructure/upperworks (lattice boom)
F-15.12-Removes superstructure/upperworks (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.12.01P |
support with blocking suitable for ground conditions and level crane |
crane is supported with blocking suitable for ground conditions and levelled using equipment to facilitate removal of superstructure/upperworks |
| F-15.12.02P |
disassemble superstructure/upperworks |
superstructure/upperworks is disassembled according to manufacturers’ specifications and instructions |
| F-15.12.03P |
disconnect hydraulic lines and electrical connections |
hydraulic lines and electrical connections are disconnected according to manufacturers’ specifications and instructions |
| F-15.12.04P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-15.12.05P |
remove superstructure/upperworks from car body/carrier |
superstructure/upperworks is removed from car body/carrier according to manufacturers’ specifications and instructions |
Range of variables
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
- equipment includes: jacks, assist cranes
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.12.01L |
demonstrate knowledge of procedures used to remove superstructure/upperworks from lattice boom cranes |
identify tools and equipment used to remove of superstructure/upperworks from lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of superstructure/upperworks from lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of superstructure/upperworks from lattice boom cranes |
| describe procedures used to remove superstructure/upperworks from lattice boom cranes |
| describe procedures used to determine blocking required based on ground conditions |
| F-15.12.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of lattice boom cranes |
identify codes, standards and regulations pertaining to disassembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
F-15.13-Removes tracks from car body (lattice boom)
F-15.13-Removes tracks from car body (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.13.01P |
extend/retract tracks |
tracks are extended/retracted according to manufacturers’ specifications and instructions |
| F-15.13.02P |
support with blocking suitable for ground conditions and level crane |
crane is supported with blocking suitable for ground conditions and levelled using equipment according to manufacturers’ specifications and instructions |
| F-15.13.03P |
disconnect hydraulic/mechanical connections for drive/outrigger systems |
hydraulic/mechanical connections for drive/outrigger systems are disconnected according to manufacturers’ specifications and instructions |
| F-15.13.04P |
support weight of track |
weight of track is supported according to manufacturers’ specifications and instructions |
| F-15.13.05P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-15.13.06P |
lift track off car body |
track is lifted off car body according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
- equipment includes: jacks, auxiliary lift equipment
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.13.01L |
demonstrate knowledge of procedures used to remove tracks from car body on lattice boom cranes |
identify tools and equipment used to remove tracks from car body on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of tracks from car body on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of tracks from car body on lattice boom cranes |
| describe procedures used to remove tracks from car body on lattice boom cranes |
| describe procedures used to determine blocking required based on ground conditions |
| F-15.13.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of lattice boom cranes |
identify codes, standards and regulations pertaining to disassembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
F-15.14-Removes outrigger boxes (lattice boom)
F-15.14-Removes outrigger boxes (lattice boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-15.14.01P |
support weight of outrigger box |
weight of outrigger box is supported according to manufacturers’ specifications and instructions |
| F-15.14.02P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-15.14.03P |
disconnect hoses and electrical wiring |
hoses and electrical wiring are disconnected according to manufacturers’ specifications and instructions |
| F-15.14.04P |
lift outrigger box from carrier |
outrigger box is lifted from carrier according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-15.14.01L |
demonstrate knowledge of procedures used to remove outrigger boxes on lattice boom cranes |
identify tools and equipment used to remove outrigger boxes on lattice boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of outrigger boxes on lattice boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of outrigger boxes on lattice boom cranes |
| describe procedures used to remove outrigger boxes on lattice boom cranes |
| F-15.14.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of lattice boom cranes |
identify codes, standards and regulations pertaining to disassembly of lattice boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
Task F-16 Assembles and disassembles telescopic boom cranes
Task descriptor
Mobile crane operators need to disassemble cranes in order to transport them to and from jobsites. Disassembly of the cranes may be necessary to comply with jurisdictional road regulations. Mobile crane operators assemble the cranes once on site. Any configuration changes require inspection. Effective communication skills are essential to ensure safety and efficiency when assembling and disassembling telescopic boom cranes.
F-16.01-Installs tracks on car body (telescopic boom)
F-16.01-Installs tracks on car body (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.01.01P |
check that car body is level |
car body is levelled |
| F-16.01.02P |
remove blocking and safety chains between drive sprockets and pads |
blocking and safety chains between drive sprockets and pads are removed |
| F-16.01.03P |
extend/retract tracks |
tracks are extended/retracted according manufacturers’ specifications and instructions |
| F-16.01.04P |
position track onto car body |
track is positioned onto car body using auxiliary lift equipment or manufacturers’ specifications and instructions for self-assembly |
| F-16.01.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions to secure track on car body |
| F-16.01.06P |
join hydraulic/mechanical connections |
hydraulic/mechanical connections are joined according to manufacturers’ specifications and instructions to complete drive/outrigger circuits |
| F-16.01.07P |
adjust track tension |
track tension is adjusted according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.01.01L |
demonstrate knowledge of telescopic boom cranes, their components, characteristics and applications |
define terminology associated with telescopic boom cranes and their components |
| identify telescopic boom crane components requiring assembly |
| F-16.01.02L |
demonstrate knowledge of procedures used to install tracks on car body of telescopic boom cranes |
identify tools and equipment used to install tracks on car body of telescopic boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of tracks on car body of telescopic boom cranes |
| interpret manufacturers’ specifications and instructionsrelating to installation of tracks on car body of telescopic boom cranes |
| describe procedures used to install tracks on car body of telescopic boom cranes |
| describe capabilities and limitations of auxiliary lift equipment |
| identify types of fasteners used in installation of tracks on car body of telescopic boom cranes |
| F-16.01.03L |
demonstrate knowledge of regulatory requirements pertaining to assembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to assembly of telescopic boom cranes |
Range of variables
- components include: tracks, car body, carrier, superstructure/upperworks, outrigger boxes, boom and jib, counterweights, hoist ropes, hook blocks, overhaul balls, attachments
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes
- fasteners include: bolts, pins and keepers, wedges
F-16.02-Installs outrigger boxes (telescopic boom)
F-16.02-Installs outrigger boxes (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.02.01P |
position outrigger box |
outrigger box is positioned according to manufacturers’ specifications and instructions |
| F-16.02.02P |
inspect for defects |
defects are detected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-16.02.03P |
clean fittings |
fittings are cleaned to avoid oil contamination and ensure ease of installation |
| F-16.02.04P |
connect hoses and electrical wiring |
hoses and electrical wiring are connected according to manufacturers’ specifications and instructions |
| F-16.02.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged hoses, fittings and cylinders; corrosion; cracks
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.02.01L |
demonstrate knowledge of telescopic boom cranes, their components, characteristics and applications |
define terminology associated with telescopic boom cranes and their components |
| F-16.02.02L |
demonstrate knowledge of procedures used to install outrigger boxes on telescopic boom cranes |
identify tools and equipment used to install outrigger boxes on telescopic boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of outrigger boxes on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of outrigger boxes on telescopic boom cranes |
| identify types of possible defects found in outrigger boxes on telescopic boom cranes |
| describe procedures used to install outrigger boxes on telescopic boom cranes |
| identify types of fasteners used in installation of outrigger boxes on telescopic boom cranes |
| describe hydraulic and electrical connections required to attach outrigger boxes to telescopic boom cranes |
| F-16.02.03L |
demonstrate knowledge of regulatory requirements pertaining to assembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to assembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged hoses, fittings and cylinders; corrosion; cracks
- fasteners include: bolts, pins and keepers, wedges
F-16.03-Installs superstructure/upperworks (telescopic boom)
F-16.03-Installs superstructure/upperworks (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.03.01P |
inspect for defects |
defects are detected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-16.03.02P |
clean surfaces and apply lubricant to pins and connection points |
surfaces are cleaned and lubricant is applied to pins and connection points according to manufacturers’ specifications and instructions to allow assembly |
| F-16.03.03P |
position superstructure/upperworks onto car body/carrier |
superstructure/upperworks is positioned onto car body/carrier according to manufacturers’ specifications and instructions |
| F-16.03.04P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions to secure superstructure/upperworks on car body/carrier |
| F-16.03.05P |
connect hydraulic lines and electrical connections |
hydraulic lines and electrical connections are connected according to manufacturers’ specifications and instructions |
Range of variables
- defects include: worn bolts, pins and bushings
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.03.01L |
demonstrate knowledge of procedures used to install superstructure/upperworks on telescopic boom cranes |
identify tools and equipment used to install superstructure/upperworks on telescopic boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of superstructure/upperworks on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of superstructure/upperworks on telescopic boom cranes |
| identify types of possible defects in superstructure/upperworks on telescopic boom cranes |
| describe procedures used to install superstructure/upperworks on telescopic boom cranes |
| identify types of fasteners used in installation of superstructure/upperworks on telescopic boom cranes |
| describe hydraulic and electrical connections required to attach superstructure/upperworks onto car body/carrier |
| F-16.03.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to assembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: worn bolts, pins and bushings
- fasteners include: bolts, pins and keepers, wedges
F-16.04-Installs main boom (telescopic boom)
F-16.04-Installs main boom (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.04.01P |
operate boom launcher or use assist cranes |
boom launcher is operated or assist cranes are used according to manufacturers’ specifications and instructions to secure main boom to superstructure/upperworks |
| F-16.04.02P |
connect hydraulic lines and electrical connections |
hydraulic lines and electrical connections are connected according to manufacturers’ specifications and instructions to complete circuits |
| F-16.04.03P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions to secure boom |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: bolts, pins and keepers
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.04.01L |
demonstrate knowledge of procedures used to install main boom on telescopic boom cranes |
identify tools and equipment used to install main boom on telescopic boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of main boom on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of main boom on telescopic boom cranes |
| describe procedures used to install main boom on telescopic boom cranes |
| identify types of fasteners used in installation of main boom on telescopic boom cranes |
| describe hydraulic and electrical connections required to attach main boom to telescopic boom cranes |
| F-16.04.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to assembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: bolts, pins and keepers
F-16.05-Installs hook blocks and overhaul ball (telescopic boom)
F-16.05-Installs hook blocks and overhaul ball (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.05.01P |
position main boom for installation |
main boom is positioned according to manufacturers’ specifications and instructions |
| F-16.05.02P |
determine block and ball overhaul weight |
block and ball overhaul weight is determined according to length of boom and reeving configuration |
| F-16.05.03P |
inspect hook block and overhaul ball for size and WLL |
hook block and overhaul ball are inspected for size and WLL according to manufacturers’ specifications and instructions |
| F-16.05.04P |
spool out stored hoist rope off of winch |
stored hoist rope is spooled out off of winch according to manufacturers’ specifications and instructions |
| F-16.05.05P |
cut and seize hoist rope if required |
hoist rope is cut and seized if required using cable cutting equipment according to manufacturers’ specifications and instructions |
| F-16.05.06P |
reeve hook block with required parts of hoist rope to lift calculated weight |
hook block is reeved with required parts of hoist rope according to manufacturers’ specifications and instructions to lift calculated weight |
| F-16.05.07P |
terminate hoist rope ends |
hoist rope ends are terminated according to manufacturers’ specifications and instructions using connections |
| F-16.05.08P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- connections include: wedge sockets, button sockets
- fasteners include: pins and keepers, wire rope clips
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.05.01L |
demonstrate knowledge of procedures used to install hook blocks and overhaul ball on telescopic boom cranes |
identify tools and equipment used to install hook blocks and overhaul ball on telescopic boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of hook blocks and overhaul ball on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of hook blocks and overhaul ball on telescopic boom cranes |
| describe procedures used to install hook blocks and overhaul ball on telescopic boom cranes |
| identify types of fasteners used in installation of hook blocks and overhaul ball on telescopic boom cranes |
| identify WLL and size of hook block and overhaul ball |
| F-16.05.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to assembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads, stored energy, broken wires, entanglement
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers, wire rope clips
F-16.06-Installs counterweights (telescopic boom)
F-16.06-Installs counterweights (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.06.01P |
inspect for defects |
defects are detected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-16.06.02P |
determine installation sequence and placement of counterweights |
installation sequence and placement of counterweights are determined according to manufacturers’ specifications and instructions |
| F-16.06.03P |
place counterweights on crane |
counterweights are placed on crane according to manufacturers’ specifications and instructions |
| F-16.06.04P |
raise assembled counterweights into position |
assembled counterweights are raised into position according to manufacturers’ specifications and instructions |
| F-16.06.05P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions to secure assembled counterweights |
Range of variables
- defects include: broken bolts, damaged threads and pins, cracks, damaged lifting lugs and eyes
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins, bolts, stack, cylinders, chains
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.06.01L |
demonstrate knowledge of procedures used to install counterweights on telescopic boom cranes |
identify tools and equipment used to install counterweights on telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of counterweights on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of counterweights on telescopic boom cranes |
| identify types of possible defects in counterweights on telescopic boom cranes |
| describe procedures used to determine sequence and placement of counterweights on telescopic boom cranes |
| identify types of fasteners used in installation of counterweights |
| F-16.06.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to assembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: broken bolts, damaged threads and pins, cracks, damaged lifting lugs and eyes
- fasteners include: pins, bolts, stack, cylinders, chains
F-16.07-Installs jibs and inserts (telescopic boom)
F-16.07-Installs jibs and inserts (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.07.01P |
inspect for defects |
defects are detected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-16.07.02P |
install inserts |
inserts are installed according to manufacturers’ specifications and instructions |
| F-16.07.03P |
erect and secure jib into working position |
jib is erected and secured into working position according to manufacturers’ specifications and instructions |
| F-16.07.04P |
adjust offset |
offset is adjusted according to manufacturers’ specifications and instructions to meet lift requirements |
| F-16.07.05P |
connect hydraulic and electrical components |
hydraulic and electrical components are connected according to manufacturers’ specifications and instructions |
| F-16.07.06P |
install fasteners |
fasteners are installed according to manufacturers’ specifications and instructions |
| F-16.07.07P |
extend telescopic jib extensions |
telescopic jib extensions are extended according to manufacturers’ specifications and instructions |
Range of variables
- defects include: bent lacings, damaged chords, broken electrical wires, dents, loose or damaged wire connections, leaking hydraulic system and connections
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- hydraulic components include: cylinders, motors, hoses
- electrical components include: anemometer, anti-two block, lights, wiring, wiring connections
- fasteners include: pins and keepers
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.07.01L |
demonstrate knowledge of procedures used to install jibs and inserts on telescopic boom cranes |
identify tools and equipment used to install jibs and inserts on telescopic boom cranes and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to installation of jibs and inserts on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to installation of jibs and inserts on telescopic boom cranes |
| describe procedures used to install jibs and inserts on telescopic boom cranes |
| identify types of fasteners used in installation of jibs and inserts on telescopic boom cranes |
| describe hydraulic and electrical connections required to attach jibs and inserts to telescopic boom cranes |
| F-16.07.02L |
demonstrate knowledge of regulatory requirements pertaining to assembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to assembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers
F-16.08-Removes jibs and inserts (telescopic boom)
F-16.08-Removes jibs and inserts (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.08.01P |
retract telescopic jib extensions |
telescopic jib extensions are retracted according to manufacturers’ specifications and instructions |
| F-16.08.02P |
disconnect electrical and hydraulic components |
electrical and hydraulic components are disconnected according to manufacturers’ specifications and instructions |
| F-16.08.03P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-16.08.04P |
return offset to stowed position |
offset is returned to stowed position according to manufacturers’ specifications and instructions |
| F-16.08.05P |
remove inserts |
inserts are removed according to manufacturers’ specifications and instructions |
| F-16.08.06P |
stow and secure jib for travel |
jib is stowed and secured for travel according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- electrical components include: anemometer, anti-two block, lights
- hydraulic components include: cylinders, motors
- fasteners include: pins and keepers
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.08.01L |
demonstrate knowledge of procedures used to remove jibs and inserts on telescopic boom cranes |
identify tools and equipment used to remove jibs and inserts on telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of jibs and inserts on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of jibs and inserts on telescopic boom cranes |
| describe procedures used to remove jibs and inserts on telescopic boom cranes |
| identify types of fasteners used in removal of jibs and inserts on telescopic boom cranes |
| describe hydraulic and electrical connections required to remove jibs and inserts to telescopic boom cranes |
| F-16.08.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to disassembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers
- electrical components include: anemometer, anti-two block, lights
- hydraulic components include: cylinders, motors
F-16.09-Removes counterweights (telescopic boom)
F-16.09-Removes counterweights (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.09.01P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-16.09.02P |
lower counterweight assembly out of position |
counterweight assembly is lowered out of position according to manufacturers’ specifications and instructions |
| F-16.09.03P |
disassemble counterweight assembly |
counterweight assembly is disassembled according to manufacturers’ specifications and instructions |
Range of variables
- fasteners include: pins, bolts, cylinders, chains
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.09.01L |
demonstrate knowledge of procedures used to remove counterweights on telescopic boom cranes |
identify tools and equipment used to remove counterweights on telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of counterweights on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of counterweights on telescopic boom cranes |
| describe procedures used to remove counterweights on telescopic boom cranes |
| F-16.09.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to disassembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
F-16.10-Removes hook blocks and overhaul ball (telescopic boom)
F-16.10-Removes hook blocks and overhaul ball (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.10.01P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-16.10.02P |
dismantle connections |
connections are dismantled according to manufacturers’ specifications and instructions |
| F-16.10.03P |
remove hoist rope from hook block |
hoist rope is removed from hook block |
| F-16.10.04P |
spool hoist rope onto winch |
hoist rope is spooled onto winch according to manufacturers’ specifications and instructions |
| F-16.10.05P |
secure line on drum |
line on drum is secured to preserve spooling |
Range of variables
- fasteners include: pins and keepers, wire rope clips
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- connections include: wedge sockets, button sockets
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.10.01L |
demonstrate knowledge of procedures used to remove hook blocks and overhaul ball from telescopic boom cranes |
identify tools and equipment used to remove hook blocks and overhaul ball from telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of hook blocks and overhaul ball from telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of hook blocks and overhaul ball from telescopic boom cranes |
| describe procedures used to remove hook blocks and overhaul ball from telescopic boom cranes |
| identify types of fasteners used with hook blocks and overhaul ball |
| F-16.10.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to disassembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads, broken wires, stored energy, entanglement
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers, wire rope clips
F-16.11-Removes main boom (telescopic boom)
F-16.11-Removes main boom (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
yes |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.11.01P |
ensure weight of main boom is supported by auxiliary lift equipment or boom launcher |
weight of main boom is supported by auxiliary lift equipment or boom launcher according to manufacturers’ specifications and instructions |
| F-16.11.02P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-16.11.03P |
disconnect hydraulic lines and electrical connections |
hydraulic lines and electrical connections are disconnected according to manufacturers’ specifications and instructions |
Range of variables
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes, boom launcher
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: pins and keepers, bolts, other hardware
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.11.01L |
demonstrate knowledge of procedures used to remove main boom from telescopic boom cranes |
identify tools and equipment used to remove main boom from telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of main boom from telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of main boom from telescopic boom cranes |
| describe procedures used to remove main boom from telescopic boom cranes |
| describe capabilities and limitations of auxiliary lift equipment |
| F-16.11.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to disassembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes, boom launcher
F-16.12-Removes outrigger boxes (telescopic boom)
F-16.12-Removes outrigger boxes (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.12.01P |
ensure weight of outrigger box is supported |
weight of outrigger box is supported using auxiliary lift equipment or is self-supported according to manufacturers’ specifications and instructions |
| F-16.12.02P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-16.12.03P |
disconnect hoses and electrical wiring |
hoses and electrical wiring are disconnected according to manufacturers’ specifications and instructions |
Range of variables
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes, gantry, A-frame, mast
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: bolts, pins and keepers
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.12.01L |
demonstrate knowledge of procedures used to remove outrigger boxes on telescopic boom cranes |
identify tools and equipment used to remove outrigger boxes on telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of outrigger boxes on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of outrigger boxes on telescopic boom cranes |
| describe procedures used to remove outrigger boxes on telescopic boom cranes |
| describe capabilities and limitations of auxiliary lift equipment |
| F-16.12.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to disassembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, mechanical failure, suspended loads
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- auxiliary lift equipment includes: forklifts, boom trucks, assist cranes, gantry, A-frame, mast
F-16.13-Removes tracks from car body (telescopic boom)
F-16.13-Removes tracks from car body (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.13.01P |
extend/retract tracks |
tracks are extended/retracted according to manufacturers’ specifications and instructions |
| F-16.13.02P |
support with blocking suitable for ground conditions and level crane |
crane is supported with blocking suitable for ground conditions and levelled using equipment according to manufacturers’ specifications and instructions |
| F-16.13.03P |
disconnect hydraulic/mechanical connections for drive/outrigger systems |
hydraulic/mechanical connections for drive/outrigger systems are disconnected according to manufacturers’ specifications and instructions |
| F-16.13.04P |
support weight of track |
weight of track is supported according to manufacturers’ specifications and instructions |
| F-16.13.05P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-16.13.06P |
remove track from car body |
track is removed from car body according to manufacturers’ specifications and instructions |
Range of variables
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
- equipment includes: jacks, auxiliary lift equipment
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.13.01L |
demonstrate knowledge of procedures used to remove tracks from car body on telescopic boom cranes |
identify tools and equipment used to remove tracks from car body on telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of tracks from car body on telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of tracks from car body on telescopic boom cranes |
| describe procedures used to remove tracks from car body on telescopic boom cranes |
| describe procedures used to determine blocking required based on ground conditions |
| F-16.13.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to disassembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
F-16.14-Removes superstructure/upperworks (telescopic boom)
F-16.14-Removes superstructure/upperworks (telescopic boom)
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-16.14.01P |
support with blocking suitable for ground conditions and level crane |
crane is supported with blocking suitable for ground conditions and levelled using equipment to facilitate removal of superstructure/upperworks |
| F-16.14.02P |
disassemble superstructure/upperworks |
superstructure/upperworks is disassembled according to manufacturers’ specifications and instructions |
| F-16.14.03P |
remove and store fasteners |
fasteners are removed and stored according to manufacturers’ specifications and instructions |
| F-16.14.04P |
disconnect hydraulic lines and electrical connections |
hydraulic lines and electrical connections are disconnected according to manufacturers’ specifications and instructions |
| F-16.14.05P |
remove superstructure/upperworks from car body/carrier |
superstructure/upperworks is removed from car body/carrier according to manufacturers’ specifications and instructions |
Range of variables
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
- equipment includes: jacks, assist cranes
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- fasteners include: bolts, pins and keepers, wedges
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-16.14.01L |
demonstrate knowledge of procedures used to remove superstructure/upperworks from telescopic boom cranes |
identify tools and equipment used to remove superstructure/upperworks from telescopic boom cranes, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to removal of superstructure/upperworks from telescopic boom cranes |
| interpret manufacturers’ specifications and instructions relating to removal of superstructure/upperworks from telescopic boom cranes |
| describe procedures used to remove superstructure/upperworks from telescopic boom cranes |
| describe procedures used to determine blocking required based on ground conditions |
| F-16.14.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of telescopic boom cranes |
identify codes, standards and regulations pertaining to disassembly of telescopic boom cranes |
Range of variables
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- ground conditions include: gravel, clay, peat, silt, asphalt, concrete
Task F-17 Assembles and disassembles specialty equipment and attachments
Task descriptor
Mobile crane operators need to assemble and disassemble specialty equipment and attachments according to manufacturers’ specifications and instructions.
F-17.01-Assembles specialty equipment and attachments
F-17.01-Assembles specialty equipment and attachments
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-17.01.01P |
select specialty equipment and attachments |
specialty equipment and attachments are selected according to job requirements |
| F-17.01.02P |
select assembly area |
assembly area is selected according to space required and site conditions |
| F-17.01.03P |
inspect for defects |
defects are detected and reported according to manufacturers’ specifications and instructions, jurisdictional regulations and company policies |
| F-17.01.04P |
clean and lubricate pins and connection points |
pins and connection points are cleaned and lubricated according to manufacturers’ specifications and instructions |
| F-17.01.05P |
connect attachments in sequence |
attachments are connected in sequence according to manufacturers’ specifications and instructions |
Range of variables
- specialty equipment include: piledriver, clamshell bucket, dragline bucket, concrete bucket, wrecking ball, magnet
- attachments include: leads, hammers, drills, safety devices, superlift
- defects include: damaged chords, lacing and hoist rope
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-17.01.01L |
demonstrate knowledge of specialty equipment, their attachments, characteristics and applications |
define terminology associated with specialty equipment and their attachments |
| identify types of specialty equipment and their attachments, and describe their characteristics and applications |
| F-17.01.02L |
demonstrate knowledge of procedures used to assemble specialty equipment and their attachments |
identify tools and equipment used to assemble specialty equipment and their attachments, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to specialty equipment and their attachments |
| interpret manufacturers’ specifications and instructions relating to assembly of specialty equipment and their attachments |
| identify types of possible defects found in specialty equipment and their attachments |
| describe procedures used to assemble specialty equipment and their attachments |
| F-17.01.03L |
demonstrate knowledge of regulatory requirements pertaining to assembly of specialty equipment and their attachments |
identify codes, standards and regulations pertaining to assembly of specialty equipment and their attachments |
Range of variables
- specialty equipment include: piledriver, clamshell bucket, dragline bucket, concrete bucket, wrecking ball, magnet
- attachments include: leads, hammers, drills, safety devices, superlift
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- defects include: damaged chords, lacing and hoist rope
F-17.02-Disassembles specialty equipment and attachments
F-17.02-Disassembles specialty equipment and attachments
| NL |
NS |
PE |
NB |
QC |
ON |
MB |
SK |
AB |
BC |
NT |
YT |
NU |
| yes |
yes |
NV |
yes |
NV |
yes |
yes |
yes |
no |
yes |
NV |
NV |
NV |
Skills
| Reference Code |
Performance Criteria |
Evidence of Attainment |
| F-17.02.01P |
select disassembly area |
disassembly area is selected according to space required and site conditions |
| F-17.02.02P |
remove attachments |
attachments are removed according to manufacturers’ specifications and instructions |
| F-17.02.03P |
demobilize specialty equipment |
specialty equipment is demobilized according to manufacturers’ specifications and instructions |
| F-17.02.04P |
perform post-operational inspection and report damage |
post-operational inspection is performed and damage is reported according to manufacturers’ specifications and instructions, company policies and jurisdictional regulations |
Range of variables
- attachments include: leads, hammers, drills, safety devices, superlift
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts
- specialty equipment include: piledriver, clamshell bucket, dragline bucket, concrete bucket, drill, wrecking ball, magnet
Knowledge
| Reference Code |
Learning Outcomes |
Learning Objectives |
| F-17.02.01L |
demonstrate knowledge of procedures used to disassemble specialty equipment and their attachments |
identify tools and equipment used to disassemble specialty equipment and their attachments, and describe their applications and procedures for use |
| identify hazards and describe safe work practices pertaining to disassembly of specialty equipment and their attachments |
| interpret manufacturers’ specifications and instructions relating to disassembly of specialty equipment and their attachments |
| describe procedures used to disassemble specialty equipment and their attachments |
| F-17.02.02L |
demonstrate knowledge of regulatory requirements pertaining to disassembly of specialty equipment and their attachments |
identify codes, standards and regulations pertaining to disassembly of specialty equipment and their attachments |
Range of variables
- specialty equipment include: piledriver, clamshell bucket, dragline bucket, concrete bucket, drill, wrecking ball, magnet
- attachments include: leads, hammers, drills, safety devices, superlift
- hazards include: pinch points, falling hazards, open machinery, mechanical failure
- manufacturers’ specifications and instructions include: load charts, configuration charts, hoist rope specifications, assembly/disassembly charts